fix some bug

qdt/i18n/QIDIStudio.pot

@@ -12950,3 +12950,66 @@ msgstr ""
 
 msgid "Switch to Device tab"
 msgstr ""
+
+msgid "Synchronize filament list from BOX."
+msgstr ""
+
+msgid "Sync Box information"
+msgstr ""
+
+msgid "Please select the printer in the list to get box info."
+msgstr ""
+
+msgid "Sync"
+msgstr ""
+
+msgid "Synchronize Box Filament Information"
+msgstr ""
+
+msgid "Add unused Box filaments to filaments list."
+msgstr ""
+
+msgid "Only synchronize filament type and color, not including Box slot information."
+msgstr ""
+
+msgid "Are you sure to synchronize the filaments from Box?"
+msgstr ""
+
+msgid "Box not connected. Please check the printer and box connect."
+msgstr ""
+
+msgid "Successfully sent. Will automatically jump to the device page in %s s."
+msgstr ""
+
+msgid "Successfully sent. Close current page in %s s."
+msgstr ""
+
+msgid "The selected printer is not connect box, please check."
+msgstr ""
+
+msgid "Failed to set the box printing slot..."
+msgstr ""
+
+msgid "This Printer has not connect the box, please check."
+msgstr ""
+
+msgid "Upper half area:  Original\nLower half area:  Filament in Box\nAnd you can click it to modify"
+msgstr ""
+
+msgid "Upper half area:  Original\nLower half area:  Filament in Box\nAnd you cannot click it to modify"
+msgstr ""
+
+msgid "BOX Slots"
+msgstr ""
+
+msgid "Use BOX"
+msgstr ""
+
+msgid "The filament information in the BOX has changed. Please resynchronize it."
+msgstr ""
+
+msgid "BOX message has change"
+msgstr ""
+
+msgid "Flushing"
+msgstr ""

qdt/i18n/cs/QIDIStudio_cs.po

@@ -14645,3 +14645,6 @@ msgstr "Informace o filamentu v BOXu se změnily. Prosím, proveďte jejich resy
 
 msgid "BOX message has change"
 msgstr "Zpráva v BOXu byla změněna."
+
+msgid "Flushing"
+msgstr "Čistící"

qdt/i18n/de/QIDIStudio_de.po

@@ -16226,3 +16226,6 @@ msgstr "Die Filamentinformationen in der BOX haben sich geändert. Bitte synchro
 
 msgid "BOX message has change"
 msgstr "BOX-Nachricht wurde geändert"
+
+msgid "Flushing"
+msgstr "Spülen"

qdt/i18n/en/QIDIStudio_en.po

@@ -16053,3 +16053,6 @@ msgstr ""
 
 msgid "BOX message has change"
 msgstr ""
+
+msgid "Flushing"
+msgstr ""

qdt/i18n/es/QIDIStudio_es.po

@@ -16236,3 +16236,6 @@ msgstr "La información del filamento en la BOX ha cambiado. Por favor, resincro
 
 msgid "BOX message has change"
 msgstr "El mensaje de la BOX ha cambiado"
+
+msgid "Flushing"
+msgstr "Lavado"

qdt/i18n/fr/QIDIStudio_fr.po

@@ -16188,3 +16188,6 @@ msgstr "Les informations du filament dans la BOX ont été modifiées. Veuillez
 
 msgid "BOX message has change"
 msgstr "Le message de la BOX a été modifié"
+
+msgid "Flushing"
+msgstr "Rinçage"

qdt/i18n/hu/QIDIStudio_hu.po

@@ -16230,3 +16230,6 @@ msgstr "A BOX-ban lévő filament információ megváltozott. Kérjük, szinkron
 
 msgid "BOX message has change"
 msgstr "A BOX üzenet megváltozott"
+
+msgid "Flushing"
+msgstr "Öblítés"

qdt/i18n/it/QIDIStudio_it.po

@@ -16235,3 +16235,6 @@ msgstr "Le informazioni sul filamento nella BOX sono cambiate. Si prega di risin
 
 msgid "BOX message has change"
 msgstr "Il messaggio della BOX è cambiato"
+
+msgid "Flushing"
+msgstr "Pulizia"

qdt/i18n/ja/QIDIStudio_ja.po

@@ -16167,3 +16167,6 @@ msgstr "BOX内のフィラメント情報が変更されました。再同期し
 
 msgid "BOX message has change"
 msgstr "BOXメッセージが変更されました"
+
+msgid "Flushing"
+msgstr "フラッシング"

qdt/i18n/ko/QIDIStudio_ko.po

@@ -14111,3 +14111,6 @@ msgstr "BOX 내 필라멘트 정보가 변경되었습니다. 다시 동기화
 
 msgid "BOX message has change"
 msgstr "BOX 메시지가 변경되었습니다"
+
+msgid "Flushing"
+msgstr "플러싱"

qdt/i18n/nl/QIDIStudio_nl.po

@@ -16230,3 +16230,6 @@ msgstr "De filamentinformatie in de BOX is gewijzigd. Synchroniseer deze opnieuw
 
 msgid "BOX message has change"
 msgstr "BOX-bericht is gewijzigd"
+
+msgid "Flushing"
+msgstr "Spoelen"

qdt/i18n/pl/QIDIStudio_pl.po

@@ -16135,3 +16135,6 @@ msgstr "Informacje o filamentach w BOX-ie uległy zmianie. Proszę je zsynchroni
 
 msgid "BOX message has change"
 msgstr "Komunikat BOX-a został zmieniony"
+
+msgid "Flushing"
+msgstr "Płukanie"

qdt/i18n/pt-BR/QIDIStudio_pt-BR.po

@@ -16219,3 +16219,6 @@ msgstr "As informações do filamento na BOX foram alteradas. Por favor, ressinc
 
 msgid "BOX message has change"
 msgstr "A mensagem da BOX foi alterada"
+
+msgid "Flushing"
+msgstr "Limpeza"

qdt/i18n/ru/QIDIStudio_ru.po

@@ -14196,3 +14196,6 @@ msgstr "Информация о филаменте в BOX была измене
 
 msgid "BOX message has change"
 msgstr "Сообщение BOX изменено"
+
+msgid "Flushing"
+msgstr "Промывка"

qdt/i18n/sv/QIDIStudio_sv.po

@@ -16250,3 +16250,6 @@ msgstr "Filamentinformationen i BOX har ändrats. Vänligen synkronisera om den.
 
 msgid "BOX message has change"
 msgstr "BOX-meddelandet har ändrats"
+
+msgid "Flushing"
+msgstr "Spolning"

qdt/i18n/tr/QIDIStudio_tr.po

@@ -14413,3 +14413,6 @@ msgstr "BOX içindeki filament bilgisi değişti. Lütfen yeniden senkronize edi
 
 msgid "BOX message has change"
 msgstr "BOX mesajı değişti"
+
+msgid "Flushing"
+msgstr "Temizleme"

qdt/i18n/uk/QIDIStudio_uk.po

@@ -16303,3 +16303,6 @@ msgstr "Інформація про філамент у BOX змінилася.
 
 msgid "BOX message has change"
 msgstr "Повідомлення BOX змінилося"
+
+msgid "Flushing"
+msgstr "Промивання"

qdt/i18n/zh_cn/QIDIStudio_zh_CN.po

@@ -20029,3 +20029,6 @@ msgstr "BOX中的耗材信息已变更，请重新同步"
 
 msgid "BOX message has change"
 msgstr "BOX消息已更新"
+
+msgid "Flushing"
+msgstr "冲刷"

resources/profiles/X 4 Series/machine/Qidi X-Plus 4 0.4 nozzle.json

@@ -11,7 +11,7 @@
     "default_print_profile": "0.20mm Standard @XPlus4",
     "printer_settings_id": "Qidi",
     "bed_exclude_area": ["0x305", "0x302", "35x302", "35x305", "305x305", "305x305", "305x305", "305x20", "293x20", "293x0", "305x0", "305x20", "305x305"],
-    "change_filament_gcode": "{if current_extruder != next_extruder}\nG1 Z{max_layer_z + 3.0} F1200\nTOOL_CHANGE_START F=[current_extruder] T=[next_extruder]\n{if long_retraction_when_cut && retraction_distance_when_cut > 2}\nDISABLE_ALL_SENSOR\nMOVE_TO_TRASH\nG1 E-[retraction_distance_when_cut] F200\nM400\n{endif}\nMOVE_TO_TRASH\nCLEAR_OOZE\nCUT_FILAMENT T=[current_extruder]\nMOVE_TO_TRASH\n{if nozzle_temperature_range_high[current_extruder] >= nozzle_temperature_range_high[next_extruder]}\nM104 S{nozzle_temperature_range_high[current_extruder]}\n{else}\nM104 S{nozzle_temperature_range_high[next_extruder]}\n{endif}\nM106 S0\nM106 P2 S0\nDISABLE_ALL_SENSOR\nUNLOAD_T[current_extruder]\nG92 E0\nG1 E25 F300\nT[next_extruder]\n{if nozzle_temperature_range_high[current_extruder] >= nozzle_temperature_range_high[next_extruder]}\nSET_HEATER_TEMPERATURE HEATER=extruder TARGET={nozzle_temperature_range_high[current_extruder]} WAIT=1\n{else}\nSET_HEATER_TEMPERATURE HEATER=extruder TARGET={nozzle_temperature_range_high[next_extruder]} WAIT=1\n{endif}\n{if long_retraction_when_cut && retraction_distance_when_cut > 2}\nG1 E{retraction_distance_when_cut - 2} F200\nG1 E2 F20\nM400\n{else}\n{if flush_length_1 > 23.7}\nG1 E{83.7 * 0.43} F{old_filament_e_feedrate}\nG1 E{83.7 * 0.02} F50\nG1 E-[old_retract_length_toolchange] F1800\nM106 S255\nM400\nG4 P5000\nM106 S0\nCLEAR_FLUSH\nG1 E{83.7 * 0.23} F{old_filament_e_feedrate}\nG1 E{83.7 * 0.02} F50\nG1 E{83.7 * 0.23} F{old_filament_e_feedrate}\nG1 E{83.7 * 0.02} F50\nG1 E{83.7 * 0.23} F{old_filament_e_feedrate}\nG1 E{83.7 * 0.02} F50\nG1 E-[old_retract_length_toolchange] F1800\n{else}\nG1 E{60 * 0.46} F{old_filament_e_feedrate}\nG1 E{60 * 0.02} F50\nM106 S255\nM400\nG4 P5000\nM106 S0\nCLEAR_FLUSH\nG1 E{60 * 0.23} F{old_filament_e_feedrate}\nG1 E{60 * 0.02} F50\nG1 E{60 * 0.23} F{old_filament_e_feedrate}\nG1 E{60 * 0.02} F50\nG1 E{60 * 0.23} F{old_filament_e_feedrate}\nG1 E{60 * 0.02} F50\nG1 E-[old_retract_length_toolchange] F1800\n{endif}\n{endif}\nM106 S255\nM400\nG4 P5000\nM106 S0\nCLEAR_FLUSH\nCLEAR_FLUSH\nG92 E0\n{if flush_length_1 > 1}\nM83\nG1 E{flush_length_1 * 0.58} F{new_filament_e_feedrate}\nG1 E{flush_length_1 * 0.02} F50\nG1 E{flush_length_1 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_1 * 0.02} F50\nG1 E{flush_length_1 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_1 * 0.02} F50\n{endif}\n{if flush_length_2 > 1}\nG1 E-[new_retract_length_toolchange] F1800\nM106 S255\nM400\nG4 P5000\nM106 S0\nCLEAR_FLUSH\nM83\nG1 E{flush_length_2 * 0.58} F{new_filament_e_feedrate}\nG1 E{flush_length_2 * 0.02} F50\nG1 E{flush_length_2 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_2 * 0.02} F50\nG1 E{flush_length_2 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_2 * 0.02} F50\n{endif}\n{if flush_length_3 > 1}\nG1 E-[new_retract_length_toolchange] F1800\nM106 S255\nM400\nG4 P5000\nM106 S0\nCLEAR_FLUSH\nM83\nG1 E{flush_length_3 * 0.58} F{new_filament_e_feedrate}\nG1 E{flush_length_3 * 0.02} F50\nG1 E{flush_length_3 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_3 * 0.02} F50\nG1 E{flush_length_3 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_3 * 0.02} F50\n{endif}\n{if flush_length_4 > 1}\nG1 E-[new_retract_length_toolchange] F1800\nM106 S255\nM400\nG4 P5000\nM106 S0\nCLEAR_FLUSH\nM83\nG1 E{flush_length_4 * 0.58} F{new_filament_e_feedrate}\nG1 E{flush_length_4 * 0.02} F50\nG1 E{flush_length_4 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_4 * 0.02} F50\nG1 E{flush_length_4 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_4 * 0.02} F50\n{endif}\nG1 E-[new_retract_length_toolchange] F1800\nM106 S255\nM109 S[new_filament_temp]\nG92 E0\nM400\nM106 S0\nCLEAR_FLUSH\nCLEAR_OOZE\nG1 Y300 F9000\nTOOL_CHANGE_END\nENABLE_ALL_SENSOR\n{endif}",
+    "change_filament_gcode": "{if current_extruder != next_extruder}\nG1 Z{max_layer_z + 3.0} F1200\nTOOL_CHANGE_START F=[current_extruder] T=[next_extruder]\n{if long_retraction_when_cut && retraction_distance_when_cut > 2}\nDISABLE_ALL_SENSOR\nG1 E-[retraction_distance_when_cut] F200\nM400\n{endif}\nCUT_FILAMENT T=[current_extruder]\nMOVE_TO_TRASH\n{if nozzle_temperature_range_high[current_extruder] >= nozzle_temperature_range_high[next_extruder]}\nM104 S{nozzle_temperature_range_high[current_extruder]}\n{else}\nM104 S{nozzle_temperature_range_high[next_extruder]}\n{endif}\nM106 S0\nM106 P2 S0\nDISABLE_ALL_SENSOR\nUNLOAD_T[current_extruder]\nG92 E0\nG1 E25 F300\nT[next_extruder]\n{if nozzle_temperature_range_high[current_extruder] >= nozzle_temperature_range_high[next_extruder]}\nSET_HEATER_TEMPERATURE HEATER=extruder TARGET={nozzle_temperature_range_high[current_extruder]} WAIT=1\n{else}\nSET_HEATER_TEMPERATURE HEATER=extruder TARGET={nozzle_temperature_range_high[next_extruder]} WAIT=1\n{endif}\n{if long_retraction_when_cut && retraction_distance_when_cut > 2}\nG1 E{retraction_distance_when_cut - 2} F200\nG1 E2 F20\nM400\n{else}\n{if filament_type[next_extruder] == \"PETG\"}\nM109 S260\n{else}\nM109 S[nozzle_temperature_range_high]\n{endif}\n{if flush_length_1 > 23.7}\nG1 E{83.7 * 0.43} F{old_filament_e_feedrate}\nG1 E{83.7 * 0.02} F50\nG1 E-[old_retract_length_toolchange] F1800\nM106 S255\nM400\nG91\nG1 X2.5 F60\nG1 X-2.5 F60\nG90\nM106 S0\nCLEAR_FLUSH\nG1 E{83.7 * 0.23} F{old_filament_e_feedrate}\nG1 E{83.7 * 0.02} F50\nG1 E{83.7 * 0.23} F{old_filament_e_feedrate}\nG1 E{83.7 * 0.02} F50\nG1 E{83.7 * 0.23} F{old_filament_e_feedrate}\nG1 E{83.7 * 0.02} F50\nG1 E-[old_retract_length_toolchange] F1800\n{else}\nG1 E{60 * 0.46} F{old_filament_e_feedrate}\nG1 E{60 * 0.02} F50\nM106 S255\nM400\nG91\nG1 X2.5 F60\nG1 X-2.5 F60\nG90\nM106 S0\nCLEAR_FLUSH\nG1 E{60 * 0.23} F{old_filament_e_feedrate}\nG1 E{60 * 0.02} F50\nG1 E{60 * 0.23} F{old_filament_e_feedrate}\nG1 E{60 * 0.02} F50\nG1 E{60 * 0.23} F{old_filament_e_feedrate}\nG1 E{60 * 0.02} F50\nG1 E-[old_retract_length_toolchange] F1800\n{endif}\n{endif}\nM106 S255\nG91\nG1 X2.5 F60\nG1 X-2.5 F60\nG90\nM106 S0\nCLEAR_FLUSH\nCLEAR_FLUSH\nG92 E0\n{if flush_length_1 > 1}\nM83\nG1 E{flush_length_1 * 0.58} F{new_filament_e_feedrate}\nG1 E{flush_length_1 * 0.02} F50\nG1 E{flush_length_1 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_1 * 0.02} F50\nG1 E{flush_length_1 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_1 * 0.02} F50\n{endif}\n{if flush_length_2 > 1}\nG1 E-[new_retract_length_toolchange] F1800\nM106 S255\nM400\nG91\nG1 X2.5 F60\nG1 X-2.5 F60\nG90\nM106 S0\nCLEAR_FLUSH\nM83\nG1 E{flush_length_2 * 0.58} F{new_filament_e_feedrate}\nG1 E{flush_length_2 * 0.02} F50\nG1 E{flush_length_2 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_2 * 0.02} F50\nG1 E{flush_length_2 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_2 * 0.02} F50\n{endif}\n{if flush_length_3 > 1}\nG1 E-[new_retract_length_toolchange] F1800\nM106 S255\nM400\nG91\nG1 X2.5 F60\nG1 X-2.5 F60\nG90\nM106 S0\nCLEAR_FLUSH\nM83\nG1 E{flush_length_3 * 0.58} F{new_filament_e_feedrate}\nG1 E{flush_length_3 * 0.02} F50\nG1 E{flush_length_3 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_3 * 0.02} F50\nG1 E{flush_length_3 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_3 * 0.02} F50\n{endif}\n{if flush_length_4 > 1}\nG1 E-[new_retract_length_toolchange] F1800\nM106 S255\nM400\nG91\nG1 X2.5 F60\nG1 X-2.5 F60\nG90\nM106 S0\nCLEAR_FLUSH\nM83\nG1 E{flush_length_4 * 0.58} F{new_filament_e_feedrate}\nG1 E{flush_length_4 * 0.02} F50\nG1 E{flush_length_4 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_4 * 0.02} F50\nG1 E{flush_length_4 * 0.18} F{new_filament_e_feedrate}\nG1 E{flush_length_4 * 0.02} F50\n{endif}\nG1 E-[new_retract_length_toolchange] F1800\nM106 S255\nM109 S[new_filament_temp]\nG92 E0\nM400\nM106 S0\nCLEAR_FLUSH\nCLEAR_OOZE\nG1 Y300 F9000\nTOOL_CHANGE_END\nENABLE_ALL_SENSOR\n{endif}",
     "default_filament_profile": ["QIDI PLA Rapido @Qidi X-Plus 4 0.4 nozzle"],
     "enable_long_retraction_when_cut": "2",
     "extruder_clearance_height_to_lid": "135",

src/slic3r/GUI/Plater.cpp

@@ -1741,7 +1741,7 @@ Sidebar::Sidebar(Plater *parent)
     wxBoxSizer* bSizer39;
     bSizer39 = new wxBoxSizer( wxHORIZONTAL );
     p->m_filament_icon = new ScalableButton(p->m_panel_filament_title, wxID_ANY, "filament");
-    p->m_staticText_filament_settings = new Label(p->m_panel_filament_title, _L("Project Filaments"), LB_PROPAGATE_MOUSE_EVENT);
+    p->m_staticText_filament_settings = new Label(p->m_panel_filament_title, _L("Filaments"), LB_PROPAGATE_MOUSE_EVENT);
     bSizer39->Add(p->m_filament_icon, 0, wxALIGN_CENTER | wxLEFT | wxRIGHT, FromDIP(10));
     bSizer39->Add( p->m_staticText_filament_settings, 0, wxALIGN_CENTER );
     bSizer39->Add(FromDIP(10), 0, 0, 0, 0);
@@ -1762,7 +1762,7 @@ Sidebar::Sidebar(Plater *parent)
     // QDS
     // add wiping dialog
     //wiping_dialog_button->SetFont(wxGetApp().normal_font());
-    p->m_flushing_volume_btn = new Button(p->m_panel_filament_title, _L("Flushing volumes"));
+    p->m_flushing_volume_btn = new Button(p->m_panel_filament_title, _L("Flushing"));
     p->m_flushing_volume_btn->SetFont(Label::Body_10);
     p->m_flushing_volume_btn->SetPaddingSize(wxSize(FromDIP(6),FromDIP(3)));
     p->m_flushing_volume_btn->SetCornerRadius(FromDIP(8));