klipper update

config/printer-tevo-flash-2018.cfg

@@ -0,0 +1,130 @@
+# Support for Tevo Flash. To use this config, the firmware should be
+# compiled for the AVR atmega2560.
+
+# Note, this config has only been tested on a modified Tevo Flash
+# (using a Bondtech BMG extruder). If using a stock printer it may be
+# necessary to update the extruder rotation_distance parameter.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PF0
+dir_pin: !PF1
+enable_pin: !PD7
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PE5
+position_endstop: -13
+position_min: -13
+position_max: 235
+homing_speed: 50
+
+[stepper_y]
+step_pin: PF6
+dir_pin: PF7
+enable_pin: !PF2
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PJ1
+position_endstop: -3
+position_min: -3
+position_max: 235
+homing_speed: 50
+
+[stepper_z]
+step_pin: PL3
+dir_pin: PL1
+enable_pin: !PK0
+microsteps: 16
+rotation_distance: 8
+position_max: 250
+endstop_pin: probe:z_virtual_endstop
+position_min: -2
+
+[stepper_z1]
+step_pin: PC1
+dir_pin: PC3
+enable_pin: !PC7
+microsteps: 16
+rotation_distance: 8
+
+[extruder]
+step_pin: PA4
+dir_pin: PA6
+enable_pin: !PA2
+microsteps: 16
+gear_ratio: 50:17
+rotation_distance: 22.598
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PB4
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK5
+control: pid
+pid_Kp: 18.547
+pid_Ki: 0.788
+pid_Kd: 109.193
+min_temp: 0
+max_temp: 250
+
+[heater_bed]
+heater_pin: PH5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK6
+control: pid
+pid_Kp: 38.824
+pid_Ki: 0.539
+pid_Kd: 698.838
+min_temp: 0
+max_temp: 70
+
+[heater_fan my_nozzle_fan]
+pin: PH4
+
+[fan]
+pin: PH6
+
+[mcu]
+serial: /dev/ttyUSB0
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 1000
+max_z_velocity: 5
+max_z_accel: 100
+
+[display]
+lcd_type: uc1701
+cs_pin: PA3
+a0_pin: PA5
+encoder_pins: ^!PC6, ^!PC4
+click_pin: ^!PC2
+kill_pin: PK2
+
+[bltouch]
+sensor_pin: PD3
+control_pin: PB5
+x_offset: 0
+y_offset: 18
+z_offset: 1.64
+samples: 3
+sample_retract_dist: 5
+
+# The homing_override section modifies the default G28 behavior
+[homing_override]
+set_position_z: 0
+axes: z
+gcode:
+    G90
+    G1 Z5 F600
+    G28 X0 Y0
+    G1 X118 Y118 F3600
+    G28 Z0
+
+# Mesh Bed Leveling.
+[bed_mesh]
+mesh_min: 5, 18
+mesh_max: 230, 228
+probe_count: 9, 9
+algorithm: bicubic