klipper update

config/printer-sunlu-s8-2020.cfg

@@ -0,0 +1,104 @@
+# This file contains pin mappings for the SUNLU S8 v1.01 (circa 2020), which
+# is a modified RAMPS v1.3 board. To use this config, the firmware should be
+# compiled for the AVR atmega2560. The following pins are available for
+# expansion (e.g. ABL): ^PD2 (Z+ endstop), PG5, PE3, PH3, PB5
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PF0
+dir_pin: !PF1
+enable_pin: !PD7
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^!PE5
+position_endstop: 0
+position_max: 310
+homing_speed: 50
+
+[stepper_y]
+step_pin: PF6
+dir_pin: !PF7
+enable_pin: !PF2
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^!PJ1
+position_endstop: 0
+position_max: 310
+homing_speed: 50
+
+[stepper_z]
+step_pin: PL3
+dir_pin: PL1
+enable_pin: !PK0
+microsteps: 16
+rotation_distance: 8
+endstop_pin: ^!PD3
+position_endstop: 0.5
+position_max: 400
+
+[extruder]
+step_pin: PA4
+dir_pin: !PA6
+enable_pin: !PA2
+microsteps: 16
+rotation_distance: 33.280
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PB4
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK5
+control: pid
+pid_kp: 25.588
+pid_ki: 1.496
+pid_kd: 109.388
+min_temp: 0
+max_temp: 250
+
+[filament_switch_sensor runout]
+pause_on_runout: True
+switch_pin: ^PE4
+
+[heater_bed]
+heater_pin: PH5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK6
+control: pid
+pid_kp: 74.786
+pid_ki: 0.766
+pid_kd: 1825.718
+min_temp: 0
+max_temp: 110
+
+[verify_heater heater_bed]
+# The stock printer heats slowly due to a large bed and no external MOSFET.
+# This should be reduced if an external MOSFET is added to increase max_temp
+# and heating rate.
+check_gain_time: 240
+
+[fan]
+pin: PH6
+
+[heater_fan fan1]
+pin: PH4
+
+[mcu]
+serial: /dev/ttyUSB0
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 10
+max_z_accel: 100
+
+[display]
+lcd_type: st7920
+cs_pin: PH1
+sclk_pin: PA1
+sid_pin: PH0
+encoder_pins: ^PC4, ^PC6
+click_pin: ^!PC2
+
+[output_pin beeper]
+pin: PC0