klipper update

config/kit-zav3d-2019.cfg

@@ -0,0 +1,156 @@
+# ZAV3D MAX config. To use this config, the firmware should be
+# compiled for the AVR atmega2560.
+
+# This is a base printer.cfg file for the ZAV3D Max printer and
+# matches the manual/build guide exactly for controllers used (MKS
+# MINI-B V1.0) and pin layout for all connected components.
+# Created by "Nurmukhamed Artykaly"
+
+# This file is only an example - be sure to review and update it
+# according to the specifics of your printer.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+# AND PLEASE READ THROUGH THE KLIPPER DOCUMENTATION FIRST!
+# https://www.klipper3d.org/Overview.html
+
+# *** THINGS TO CHANGE/CHECK: ***
+# Arduino paths                         [mcu] section
+# Thermistor types                      [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
+# FSR switch (z endstop) location       [homing_override] section
+# FSR switch (z endstop) offset for Z0  [stepper_z] section
+# Probe points                          [quad_gantry_level] section
+# Min & Max gantry corner postions      [quad_gantry_level] section
+# PID tune                              [extruder] and [heater_bed] sections
+# Fine tune E steps                     [extruder] section
+
+
+[stepper_x]
+step_pin: PF0
+dir_pin: PF1
+enable_pin: !PD7
+microsteps: 16
+rotation_distance: 32
+endstop_pin: ^PE5
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+# The stepper_y section is used to describe the Y axis as well as the
+# stepper controlling the X-Y movement.
+[stepper_y]
+step_pin: PF6
+dir_pin: PF7
+enable_pin: !PF2
+microsteps: 16
+rotation_distance: 32
+endstop_pin: ^PJ1
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+## Configuration with Z Endstop, without Probe tool like BLTOUCH or others.
+#[stepper_z]
+#step_pin: PL3
+#dir_pin: PL1
+#enable_pin: !PK0
+#microsteps: 16
+#rotation_distance: 8
+## I used Z_MAX_ENDSTOP
+#endstop_pin: ^PD2
+## More about z-calibration is here https://vk.com/topic-107680682_34101598
+#position_endstop: 235
+#position_max: 235
+#homing_positive_dir: true
+
+## Configuration for Bltouch probe tool.
+## Read more about BLTOUCH here https://www.klipper3d.org/BLTouch.html
+[stepper_z]
+step_pin: PL3
+dir_pin: PL1
+enable_pin: !PK0
+microsteps: 16
+rotation_distance: 8
+position_min: -3
+position_max: 230
+endstop_pin: probe:z_virtual_endstop
+
+## Configuration with PID Calibration.
+## Read more here https://www.klipper3d.org/Config_checks.html
+[extruder]
+step_pin: PA4
+dir_pin: !PA6
+enable_pin: !PA2
+microsteps: 16
+rotation_distance: 13.5744
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PB4
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK5
+min_temp: 0
+max_temp: 250
+control: pid
+pid_kp: 26.596
+pid_ki: 1.166
+pid_kd: 151.598
+
+## Configuration with PID Calibration.
+## Read more here https://www.klipper3d.org/Config_checks.html
+[heater_bed]
+heater_pin: PH5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK6
+min_temp: 0
+max_temp: 130
+control: pid
+pid_kp: 73.517
+pid_ki: 1.822
+pid_kd: 741.600
+
+[fan]
+pin: PH6
+
+[mcu]
+serial: /dev/ttyACM0
+
+[printer]
+kinematics: corexy
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 25
+max_z_accel: 30
+
+[bltouch]
+sensor_pin: ^PD3
+control_pin: PH4
+x_offset: 39
+y_offset: 11
+z_offset: 0.9
+pin_up_touch_mode_reports_triggered: false
+samples: 2
+sample_retract_dist: 3.0
+
+[bed_mesh]
+speed: 100
+horizontal_move_z: 5
+mesh_min: 69, 41
+mesh_max: 189, 161
+probe_count: 3, 3
+
+[homing_override]
+set_position_z: 6
+axes: z
+gcode:
+        G90
+        G1 Z10 F6000
+        G28 X Y
+        G1 X100 Y100 F6000
+        G28 Z0
+        G1 X100 Y100 Z10a
+
+[gcode_macro G29]
+gcode:
+        G28
+        G1 Z10 F600
+        BED_MESH_CALIBRATE