klipper update

config/generic-einsy-rambo.cfg

@@ -0,0 +1,118 @@
+# This file contains common pin mappings for Einsy Rambo boards. To use
+# this config, the firmware should be compiled for the AVR atmega2560.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+# Note: The Einsy boards sold by Prusa have defective firmware on the
+# usb-to-serial chip that make the boards unusable with Klipper
+# (boards sold by Ultimaker do not have this issue). See
+# https://github.com/PrusaOwners/mk3-32u2-firmware for a fixed
+# usb-to-serial firmware.
+
+[stepper_x]
+step_pin: PC0
+dir_pin: PL0
+enable_pin: !PA7
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PB6
+#endstop_pin: tmc2130_stepper_x:virtual_endstop
+position_endstop: 0
+position_max: 250
+
+[tmc2130 stepper_x]
+cs_pin: PG0
+run_current: .5
+sense_resistor: 0.220
+diag1_pin: !PK2
+
+[stepper_y]
+step_pin: PC1
+dir_pin: !PL1
+enable_pin: !PA6
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PB5
+#endstop_pin: tmc2130_stepper_y:virtual_endstop
+position_endstop: 0
+position_max: 210
+
+[tmc2130 stepper_y]
+cs_pin: PG2
+run_current: .5
+sense_resistor: 0.220
+diag1_pin: !PK7
+
+[stepper_z]
+step_pin: PC2
+dir_pin: PL2
+enable_pin: !PA5
+microsteps: 16
+rotation_distance: 8
+endstop_pin: ^PB4
+#endstop_pin: tmc2130_stepper_z:virtual_endstop
+position_endstop: 0.5
+position_max: 200
+
+[tmc2130 stepper_z]
+cs_pin: PK5
+run_current: .5
+sense_resistor: 0.220
+diag1_pin: !PK6
+
+[extruder]
+step_pin: PC3
+dir_pin: PL6
+enable_pin: !PA4
+microsteps: 16
+rotation_distance: 33.500
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PE5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PF0
+control: pid
+pid_Kp: 22.2
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 250
+
+[tmc2130 extruder]
+cs_pin: PK4
+run_current: .5
+sense_resistor: 0.220
+diag1_pin: !PK3
+
+[heater_bed]
+heater_pin: PG5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PF2
+control: watermark
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: PH5
+
+#[heater_fan heatbreak_cooling_fan]
+#pin: PH3
+
+[temperature_sensor board_sensor]
+sensor_pin: PF6
+sensor_type: TDK NTCG104LH104JT1
+min_temp: 0
+max_temp: 50
+
+[mcu]
+serial: /dev/ttyACM0
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+[static_digital_output yellow_led]
+pins: !PB7