mirror of
https://github.com/QIDITECH/klipper.git
synced 2026-02-01 16:38:41 +03:00
plus4的klipper版本
This commit is contained in:
whb0514
@@ -4,9 +4,9 @@ This document describes Klipper's CAN bus support.
|
||||
|
||||
## Device Hardware
|
||||
|
||||
Klipper currently only supports CAN on stm32 chips. In addition, the
|
||||
micro-controller chip must support CAN and it must be on a board that
|
||||
has a CAN transceiver.
|
||||
Klipper currently supports CAN on stm32, SAME5x, and rp2040 chips. In
|
||||
addition, the micro-controller chip must be on a board that has a CAN
|
||||
transceiver.
|
||||
|
||||
To compile for CAN, run `make menuconfig` and select "CAN bus" as the
|
||||
communication interface. Finally, compile the micro-controller code
|
||||
@@ -14,44 +14,35 @@ and flash it to the target board.
|
||||
|
||||
## Host Hardware
|
||||
|
||||
In order to use a CAN bus, it is necessary to have a host adapter.
|
||||
There are currently two common options:
|
||||
|
||||
1. Use a
|
||||
[Waveshare Raspberry Pi CAN hat](https://www.waveshare.com/rs485-can-hat.htm)
|
||||
or one of its many clones.
|
||||
|
||||
2. Use a USB CAN adapter (for example
|
||||
[https://hacker-gadgets.com/product/cantact-usb-can-adapter/](https://hacker-gadgets.com/product/cantact-usb-can-adapter/)). There
|
||||
are many different USB to CAN adapters available - when choosing
|
||||
one, we recommend verifying it can run the
|
||||
[candlelight firmware](https://github.com/candle-usb/candleLight_fw).
|
||||
(Unfortunately, we've found some USB adapters run defective
|
||||
firmware and are locked down, so verify before purchasing.)
|
||||
In order to use a CAN bus, it is necessary to have a host adapter. It
|
||||
is recommended to use a "USB to CAN adapter". There are many different
|
||||
USB to CAN adapters available from different manufacturers. When
|
||||
choosing one, we recommend verifying that the firmware can be updated
|
||||
on it. (Unfortunately, we've found some USB adapters run defective
|
||||
firmware and are locked down, so verify before purchasing.) Look for
|
||||
adapters that can run Klipper directly (in its "USB to CAN bridge
|
||||
mode") or that run the
|
||||
[candlelight firmware](https://github.com/candle-usb/candleLight_fw).
|
||||
|
||||
It is also necessary to configure the host operating system to use the
|
||||
adapter. This is typically done by creating a new file named
|
||||
`/etc/network/interfaces.d/can0` with the following contents:
|
||||
```
|
||||
auto can0
|
||||
allow-hotplug can0
|
||||
iface can0 can static
|
||||
bitrate 500000
|
||||
bitrate 1000000
|
||||
up ifconfig $IFACE txqueuelen 128
|
||||
```
|
||||
|
||||
Note that the "Raspberry Pi CAN hat" also requires
|
||||
[changes to config.txt](https://www.waveshare.com/wiki/RS485_CAN_HAT).
|
||||
|
||||
## Terminating Resistors
|
||||
|
||||
A CAN bus should have two 120 ohm resistors between the CANH and CANL
|
||||
wires. Ideally, one resistor located at each the end of the bus.
|
||||
|
||||
Note that some devices have a builtin 120 ohm resistor (for example,
|
||||
the "Waveshare Raspberry Pi CAN hat" has a soldered on resistor that
|
||||
can not be easily removed). Some devices do not include a resistor at
|
||||
all. Other devices have a mechanism to select the resistor (typically
|
||||
by connecting a "pin jumper"). Be sure to check the schematics of all
|
||||
Note that some devices have a builtin 120 ohm resistor that can not be
|
||||
easily removed. Some devices do not include a resistor at all. Other
|
||||
devices have a mechanism to select the resistor (typically by
|
||||
connecting a "pin jumper"). Be sure to check the schematics of all
|
||||
devices on the CAN bus to verify that there are two and only two 120
|
||||
Ohm resistors on the bus.
|
||||
|
||||
@@ -73,7 +64,7 @@ powered and wired correctly, and then run:
|
||||
If uninitialized CAN devices are detected the above command will
|
||||
report lines like the following:
|
||||
```
|
||||
Found canbus_uuid=11aa22bb33cc
|
||||
Found canbus_uuid=11aa22bb33cc, Application: Klipper
|
||||
```
|
||||
|
||||
Each device will have a unique identifier. In the above example,
|
||||
@@ -95,22 +86,18 @@ canbus_uuid: 11aa22bb33cc
|
||||
## USB to CAN bus bridge mode
|
||||
|
||||
Some micro-controllers support selecting "USB to CAN bus bridge" mode
|
||||
during "make menuconfig". This mode may allow one to use a
|
||||
during Klipper's "make menuconfig". This mode may allow one to use a
|
||||
micro-controller as both a "USB to CAN bus adapter" and as a Klipper
|
||||
node.
|
||||
|
||||
When Klipper uses this mode the micro-controller appears as a "USB CAN
|
||||
bus adapter" under Linux. The "Klipper bridge mcu" itself will appear
|
||||
as if was on this CAN bus - it can be identified via `canbus_query.py`
|
||||
and configured like other CAN bus Klipper nodes. It will appear
|
||||
alongside other devices that are actually on the CAN bus.
|
||||
as if it was on this CAN bus - it can be identified via
|
||||
`canbus_query.py` and it must be configured like other CAN bus Klipper
|
||||
nodes.
|
||||
|
||||
Some important notes when using this mode:
|
||||
|
||||
* The "bridge mcu" is not actually on the CAN bus. Messages to and
|
||||
from it do not consume bandwidth on the CAN bus. The mcu can not be
|
||||
seen by other adapters that may be on the CAN bus.
|
||||
|
||||
* It is necessary to configure the `can0` (or similar) interface in
|
||||
Linux in order to communicate with the bus. However, Linux CAN bus
|
||||
speed and CAN bus bit-timing options are ignored by Klipper.
|
||||
@@ -118,7 +105,37 @@ Some important notes when using this mode:
|
||||
menuconfig" and the bus speed specified in Linux is ignored.
|
||||
|
||||
* Whenever the "bridge mcu" is reset, Linux will disable the
|
||||
corresponding `can0` interface. Generally, this may require running
|
||||
commands such as "ip up" to restart the interface. Thus, Klipper
|
||||
FIRMWARE_RESTART commands (or regular RESTART after a config change)
|
||||
may require restarting the `can0` interface.
|
||||
corresponding `can0` interface. To ensure proper handling of
|
||||
FIRMWARE_RESTART and RESTART commands, it is recommended to use
|
||||
`allow-hotplug` in the `/etc/network/interfaces.d/can0` file. For
|
||||
example:
|
||||
```
|
||||
allow-hotplug can0
|
||||
iface can0 can static
|
||||
bitrate 1000000
|
||||
up ifconfig $IFACE txqueuelen 128
|
||||
```
|
||||
|
||||
* The "bridge mcu" is not actually on the CAN bus. Messages to and
|
||||
from the bridge mcu will not be seen by other adapters that may be
|
||||
on the CAN bus.
|
||||
|
||||
* The available bandwidth to both the "bridge mcu" itself and all
|
||||
devices on the CAN bus is effectively limited by the CAN bus
|
||||
frequency. As a result, it is recommended to use a CAN bus frequency
|
||||
of 1000000 when using "USB to CAN bus bridge mode".
|
||||
|
||||
Even at a CAN bus frequency of 1000000, there may not be sufficient
|
||||
bandwidth to run a `SHAPER_CALIBRATE` test if both the XY steppers
|
||||
and the accelerometer all communicate via a single "USB to CAN bus"
|
||||
interface.
|
||||
|
||||
* A USB to CAN bridge board will not appear as a USB serial device, it
|
||||
will not show up when running `ls /dev/serial/by-id`, and it can not
|
||||
be configured in Klipper's printer.cfg file with a `serial:`
|
||||
parameter. The bridge board appears as a "USB CAN adapter" and it is
|
||||
configured in the printer.cfg as a [CAN node](#configuring-klipper).
|
||||
|
||||
## Tips for troubleshooting
|
||||
|
||||
See the [CAN bus troubleshooting](CANBUS_Troubleshooting.md) document.
|
||||
|
||||
Reference in New Issue
Block a user