Merge pull request #89 from aidan-gibson/main

typo fix

README.md

@@ -7,21 +7,18 @@ Q1 Pro is a 3D printer that uses Klipper as its foundation. This repository is u
 
 For convenience, QIDI provides version-specific packaged files. Please download the necessary compressed package file prefixed with "Q1_Pro." Select the appropriate branch for download, with each branch name reflecting the corresponding version.
 
-## V4.4.21 Update Content
+## V4.4.24 Update Content
 
 **Note:** After updating, the Klipper configuration file will be replaced. The previous configuration file will be backed up as `printer_{datetime}.cfg`, printer recalibration will be required.
 
-1. Fixed slow response to filament break detection
+1. Update the QIDI-LINK connection method to make the connection more secure.
 
-2. Fixed issue with configuration file not being backed up during update
+2. Added Fluidd account management module
 
-3. Adjusted silent print switch position
+3. Fixed the issue of USB not being read on startup
 
-4. Chamber light setting are no longer affected by the screen off state.
+4. Updated configuration files
     
-5. Updated configuration file
-    
-    Enable chamber exhaust fan by default when chamber temp set to 0. Board fan associated with x y motor drive instead of z axis.
 
 We also addressed an issue where the display of connected WiFi names containing Unicode characters appeared blank, and this has been fixed.
 
@@ -59,5 +56,5 @@ We extend our gratitude to the developers and maintainers of these open-source p
 | Software      |Official| QIDI edition                                                                     |
 | ------------- |----------| -------------------------------------------------------------------------------- |
 | **Klipper**   |**[https://github.com/Klipper3d/klipper](https://github.com/Klipper3d/klipper)**| **[https://github.com/QIDITECH/klipper](https://github.com/QIDITECH/klipper)**   |
-| **Moonraker** |**[https://github.com/Arksine/moonraker](https://github.com/Arksine/moonraker)**| **[https://github.com/QIDITECH/moonrake](https://github.com/QIDITECH/moonrake)** |
+| **Moonraker** |**[https://github.com/Arksine/moonraker](https://github.com/Arksine/moonraker)**| **[https://github.com/QIDITECH/moonraker](https://github.com/QIDITECH/moonraker)** |
 |**Fluidd**|**[https://github.com/fluidd-core/fluidd](https://github.com/fluidd-core/fluidd)**||

config/gcode_macro.cfg

@@ -163,12 +163,10 @@ gcode:
     {% set hotendtemp = params.HOTEND|int %}
     {% set chambertemp = params.CHAMBER|default(0)|int %}
     set_zoffset
-    {% if chambertemp == 0 %}
+
-        M106 P3 S255
-    {% endif %}
     M104 S0
     M140 S{bedtemp}    
-    M141 S{chambertemp}
+#    M141 S{chambertemp}
     G28    
     CLEAR_NOZZLE HOTEND={hotendtemp}
 
@@ -178,10 +176,13 @@ gcode:
     G0 Z50 F600
     G0 X0 Y0  F6000
     
-    M191 S{chambertemp}
-    M109 S{hotendtemp}
-    M204 S10000
 
+    M109 S{hotendtemp}
+    M141 S{chambertemp}    
+    M204 S10000
+    {% if chambertemp == 0 %}
+        M106 P3 S255
+    {% endif %}
     ENABLE_ALL_SENSOR
     save_last_file
 
@@ -661,7 +662,7 @@ gcode:
     G92 E0
     G1  E-90 F800
     M400
-    M118 Unload finish
+    M118 Filament unloaded
 
 [gcode_macro M604]
 description: load filament
@@ -670,7 +671,7 @@ gcode:
     M83
     G1 E80 F400
     M400
-    M118 Load finish
+    M118 Filament loaded
 
 [output_pin sound]
 pin: gpio8

config/printer.cfg

@@ -445,6 +445,8 @@ probe_points:
 
 [idle_timeout]
 timeout: 43200
+gcode:
+    PRINT_END
 
 [pause_resume]