diff --git a/UI/MATE_272_480.HMI b/UI/MATE_272_480.HMI index 2776b1c..f1974d2 100644 Binary files a/UI/MATE_272_480.HMI and b/UI/MATE_272_480.HMI differ diff --git a/UI/MATE_272_480.tft b/UI/MATE_272_480.tft index dda5abe..31d9db3 100644 Binary files a/UI/MATE_272_480.tft and b/UI/MATE_272_480.tft differ diff --git a/config/gcode_macro.cfg b/config/gcode_macro.cfg index 51c46ed..eedb10a 100644 --- a/config/gcode_macro.cfg +++ b/config/gcode_macro.cfg @@ -35,10 +35,17 @@ gcode: {% set z = printer.save_variables.variables.z_offset %} SET_GCODE_OFFSET Z={z} MOVE=0 -[gcode_macro CLEAR_NOZZLE] +[gcode_macro CLEAR_NOZZLE_PLR] gcode: - {% set hotendtemp = params.HOTEND|int %} - G1 Z60 F600 + {% set hotendtemp = params.HOTEND|default(250)|int %} + {% if (printer.gcode_move.position.z ) < 35 %} + G90 + G1 Z35 F900 + {% else %} + G91 + G1 Z5 F900 + G90 + {% endif %} G1 X97 F9000 G1 Y254 F9000 @@ -47,6 +54,43 @@ gcode: G92 E0 G1 E80 F400 M106 S255 + + G1 X98 F500 + G1 X85 F2000 + G1 X98 F2000 + G1 X85 F2000 + G1 X98 F2000 + G1 X85 F2000 + G1 X98 F2000 + G1 X85 F2000 + G1 X98 F2000 + G1 X85 F2000 + G1 X98 F2000 + G1 X85 F2000 + G1 X98 F2000 + G1 Y240 F9000 + + + +[gcode_macro CLEAR_NOZZLE] +gcode: + {% set hotendtemp = params.HOTEND|int %} + {% if (printer.gcode_move.position.z ) < 35 %} + G1 Z35 F900 + {% else %} + G91 + G1 Z5 F900 + G90 + {% endif %} + G1 X97 F9000 + G1 Y254 F9000 + + M109 S{hotendtemp} + + G92 E0 + G1 E80 F400 + M106 S255 + M400 M106 P2 S0 M104 S0 TEMPERATURE_WAIT SENSOR=extruder MAXIMUM={hotendtemp-30} @@ -120,7 +164,7 @@ gcode: CLEAR_NOZZLE HOTEND={hotendtemp} M190 S{bedtemp} - Z_TILT_ADJUST +# Z_TILT_ADJUST G29 G0 Z50 F600 G0 X0 Y0 F6000 @@ -129,11 +173,21 @@ gcode: M109 S{hotendtemp} M204 S10000 + ENABLE_ALL_SENSOR + save_last_file + +[gcode_macro ENABLE_ALL_SENSOR] +gcode: ENABLE_FILAMENT_WIDTH_SENSOR RESET_FILAMENT_WIDTH_SENSOR query_filament_width SET_FILAMENT_SENSOR SENSOR=fila ENABLE=1 - save_last_file + +[gcode_macro DISABLE_ALL_SENSOR] +gcode: + SET_FILAMENT_SENSOR SENSOR=fila ENABLE=0 + DISABLE_FILAMENT_WIDTH_SENSOR + [gcode_macro AUTOTUNE_SHAPERS] variable_autotune_shapers: 'ei' @@ -149,7 +203,7 @@ gcode: SET_STEPPER_ENABLE STEPPER=stepper_z1 enable=1 SET_STEPPER_ENABLE STEPPER=extruder enable=0 -[gcode_macro KINEMATIC_POSITION] +[gcode_macro DETECT_INTERRUPTION] gcode: {% set was_interrupted = printer.save_variables.variables.was_interrupted %} {% if was_interrupted %} @@ -165,12 +219,12 @@ gcode: SET_STEPPER_ENABLE STEPPER=stepper_z1 enable=1 BED_MESH_CLEAR SET_FILAMENT_SENSOR SENSOR=fila ENABLE=0 - {% set was_interrupted = printer.save_variables.variables.was_interrupted %} - {% if was_interrupted %} - M118 Detected unexpected interruption during the last print. Do you want to resume printing? (Do not move the extruder before resuming.) - M118 Yes: RESUME_INTERRUPTED - M118 No: CLEAR_LAST_FILE - {% endif %} + # {% set was_interrupted = printer.save_variables.variables.was_interrupted %} + # {% if was_interrupted %} + # M118 Detected unexpected interruption during the last print. Do you want to resume printing? (Do not move the extruder before resuming.) + # M118 Yes: RESUME_INTERRUPTED + # M118 No: CLEAR_LAST_FILE + # {% endif %} [homing_override] axes:xyz @@ -214,9 +268,9 @@ gcode: {% if params.Z is undefined %} SET_KINEMATIC_POSITION X=0 SET_KINEMATIC_POSITION Y=0 - SET_KINEMATIC_POSITION Z={printer.toolhead.axis_maximum.z-5} + SET_KINEMATIC_POSITION Z={printer.toolhead.axis_maximum.z-10} G91 - G1 Z5 F600 + G1 Z7 F600 G1 X10 F2400 G1 Y10 F2400 G4 P2000 @@ -239,7 +293,7 @@ gcode: BEEP I=1 DUR=100 G1 X10 F1200 - SET_KINEMATIC_POSITION Z={printer.toolhead.axis_maximum.z-5} + SET_KINEMATIC_POSITION Z={printer.toolhead.axis_maximum.z-10} G90 G1 X120 Y120 F7800 @@ -282,8 +336,7 @@ gcode: SET_STEPPER_ENABLE STEPPER=stepper_z1 enable=1 SET_STEPPER_ENABLE STEPPER=extruder enable=0 - SET_FILAMENT_SENSOR SENSOR=fila ENABLE=0 - DISABLE_FILAMENT_WIDTH_SENSOR + DISABLE_ALL_SENSOR SET_GCODE_OFFSET Z=0 MOVE=0 BED_MESH_CLEAR G31 @@ -321,8 +374,7 @@ gcode: SET_STEPPER_ENABLE STEPPER=stepper_z1 enable=1 SET_STEPPER_ENABLE STEPPER=extruder enable=0 - SET_FILAMENT_SENSOR SENSOR=fila ENABLE=0 - DISABLE_FILAMENT_WIDTH_SENSOR + DISABLE_ALL_SENSOR SET_GCODE_OFFSET Z=0 MOVE=0 BED_MESH_CLEAR G31 @@ -345,6 +397,8 @@ gcode: SET_FILAMENT_SENSOR SENSOR=fila ENABLE=0 ; disable filament sensor SAVE_GCODE_STATE NAME=PAUSE ; save current print position for resume BASE_PAUSE ; pause print + G92 E0 + G1 E-5 F1800 {% if (printer.gcode_move.position.z ) < z %} G91 ; relative positioning G1 Z{z} F900 ; raise Z up by z hop amount @@ -554,7 +608,7 @@ gcode: [gcode_macro M4028] gcode: G28 - Z_TILT_ADJUST +# Z_TILT_ADJUST G28 get_zoffset M400 @@ -569,12 +623,16 @@ gcode: M118 Position init complete CLEAR_NOZZLE HOTEND=240 - Z_TILT_ADJUST +# Z_TILT_ADJUST G28 get_zoffset [gcode_macro M4030] gcode: + REVERSE_HOMING + G91 + G1 Z-30 + G90 BED_MESH_CLEAR SET_GCODE_OFFSET Z=0 MOVE=0 G28 @@ -590,7 +648,7 @@ gcode: G0 E15 F400 G4 P1000 G92 E0 - G1 E-80 F800 + G1 E-90 F800 M400 M118 Unload finish @@ -603,7 +661,7 @@ gcode: M118 Load finish [output_pin sound] -pin: U_1:PA13 +pin: gpio8 value:0 [gcode_macro beep_on] diff --git a/config/printer.cfg b/config/printer.cfg index 2d9e38e..82ff99f 100644 --- a/config/printer.cfg +++ b/config/printer.cfg @@ -10,6 +10,8 @@ # modify: delete comments # add time_update macro # [bed_mesh] 6,6 ->8,8 +#V4.4.19 2024-4-16 +# modify: add [chamber_fan chamber_fan] [include timelapse.cfg] [include Adaptive_Mesh.cfg] [include gcode_macro.cfg] @@ -180,13 +182,17 @@ microsteps: 128 rotation_distance: 4 full_steps_per_rotation: 200 endstop_pin:probe:z_virtual_endstop #U_1:PC3 for Z-max +endstop_pin_reverse:tmc2209_stepper_z:virtual_endstop position_endstop:-0.2 +position_endstop_reverse:248 position_max:248 -position_min: -6 +position_min: -4 homing_speed: 8 +homing_speed_reverse: 8 second_homing_speed: 10 homing_retract_dist: 5.0 homing_positive_dir:false +homing_positive_dir_reverse:true step_pulse_duration:0.0000001 [stepper_z1] @@ -197,6 +203,7 @@ microsteps: 128 rotation_distance: 4 full_steps_per_rotation: 200 step_pulse_duration:0.0000001 +endstop_pin_reverse:tmc2209_stepper_z1:virtual_endstop [z_tilt] z_positions: @@ -244,6 +251,8 @@ run_current: 0.6 #hold_current: 0.17 interpolate: True stealthchop_threshold: 9999999999 +diag_pin:^U_1:PC12 +driver_SGTHRS:140 [tmc2209 stepper_z1] uart_pin:U_1: PB7 @@ -251,6 +260,8 @@ run_current: 0.6 #hold_current: 0.17 interpolate: True stealthchop_threshold: 9999999999 +diag_pin:^U_1:PA13 +driver_SGTHRS:140 [heater_bed] heater_pin: U_1:PB10 @@ -312,15 +323,16 @@ hardware_pwm: false kick_start_time: 0.100 off_below: 0.0 -[heater_fan chamber_fan] +[chamber_fan chamber_fan] pin:U_1:PA4 max_power: 1.0 shutdown_speed: 0 kick_start_time: 0.5 -heater: chamber -heater_temp: 35 +heater:chamber fan_speed: 1.0 off_below: 0 +idle_timeout:60 +idle_speed:1.0 [heater_fan hotend_fan] pin:gpio25 diff --git a/include/event.h b/include/event.h index 8394336..5ab3c8c 100644 --- a/include/event.h +++ b/include/event.h @@ -255,4 +255,8 @@ void refresh_page_auto_unload(); int get_mks_ethernet(); void set_mks_ethernet(int target); +std::string hex_to_utf8(const std::string& hex); + +void check_print_interrupted(); + #endif diff --git a/include/ui.h b/include/ui.h index 4a4628b..e86bde6 100644 --- a/include/ui.h +++ b/include/ui.h @@ -420,6 +420,15 @@ #define TJC_PAGE_INSTALLING 90 +#define TJC_PAGE_AUTO_WARNING 91 +#define TJC_PAGE_AUTO_WARNING_YES 0x00 + +#define TJC_PAGE_CALIBRATE_WARNING 92 +#define TJC_PAGE_CALIBRATE_WARNING_NEXT 0x00 +#define TJC_PAGE_CALIBRATE_WARNING_BACK 0x01 + +#define TJC_PAGE_RE_PRINTING 93 + void parse_cmd_msg_from_tjc_screen(char *cmd); void page_to(int page_id); void tjc_event_clicked_handler(int page_id, int widget_id, int type_id); diff --git a/main.cpp b/main.cpp index 70dece5..b9d4a21 100644 --- a/main.cpp +++ b/main.cpp @@ -240,7 +240,7 @@ int main(int argc, char** argv) { mks_get_version(); sleep(3); - send_cmd_val(tty_fd, "logo.version", "18"); // CLL 检测UI与SOC版本是否匹配4.4.18版本输出标记数字为18 + send_cmd_val(tty_fd, "logo.version", "19"); // CLL 检测UI与SOC版本是否匹配4.4.19版本输出标记数字为19 if (find_screen_tft_file == false) { previous_page_id = TJC_PAGE_LOGO; if (get_mks_oobe_enabled() == true) { diff --git a/src/event.cpp b/src/event.cpp index 3b0cbc7..09f60bf 100644 --- a/src/event.cpp +++ b/src/event.cpp @@ -364,6 +364,8 @@ extern std::string thumbnail_path; extern bool cache_clicked; +int unhomed_move_mode = 0; // CLL 用于保存上次按下的移动按钮，当触发需先归位操作时进行移动, 1(x up),2(x down),3(y up),4(y down),5(z up),6(z down) + // CLL 以下变量用于修复gcode响应函数和refresh函数之间的冲突(gcode响应函数需设置变量在refresh_page_show中统一改变页面，否则会产生冲突) bool jump_to_move_pop_1 = false; bool jump_to_move_pop_2 = false; @@ -404,6 +406,42 @@ void refresh_page_show() { page_to(TJC_PAGE_MOVE_POP_1); } if (jump_to_move_pop_2 == true) { + switch (unhomed_move_mode) + { + case 1: // X_UP + ep->Send(json_run_a_gcode("SET_KINEMATIC_POSITION Z=150\nSET_KINEMATIC_POSITION X=150\nSET_KINEMATIC_POSITION Y=150\n")); + ep->Send(json_run_a_gcode("G91\nG1 X10 F3000\nG90\nM84\n")); + break; + + case 2: // X_DOWN + ep->Send(json_run_a_gcode("SET_KINEMATIC_POSITION Z=150\nSET_KINEMATIC_POSITION X=150\nSET_KINEMATIC_POSITION Y=150\n")); + ep->Send(json_run_a_gcode("G91\nG1 X-10 F3000\nG90\nM84\n")); + break; + + case 3: // Y_UP + ep->Send(json_run_a_gcode("SET_KINEMATIC_POSITION Z=150\nSET_KINEMATIC_POSITION X=150\nSET_KINEMATIC_POSITION Y=150\n")); + ep->Send(json_run_a_gcode("G91\nG1 Y10 F3000\nG90\nM84\n")); + break; + + case 4: // Y_DOWN + ep->Send(json_run_a_gcode("SET_KINEMATIC_POSITION Z=150\nSET_KINEMATIC_POSITION X=150\nSET_KINEMATIC_POSITION Y=150\n")); + ep->Send(json_run_a_gcode("G91\nG1 Y-10 F3000\nG90\nM84\n")); + break; + + case 5: // Z_UP + ep->Send(json_run_a_gcode("SET_KINEMATIC_POSITION Z=150\nSET_KINEMATIC_POSITION X=150\nSET_KINEMATIC_POSITION Y=150\n")); + ep->Send(json_run_a_gcode("G91\nG1 Z-10 F600\nG90\nM84\n")); + break; + + case 6: // Z_DOWN + ep->Send(json_run_a_gcode("SET_KINEMATIC_POSITION Z=150\nSET_KINEMATIC_POSITION X=150\nSET_KINEMATIC_POSITION Y=150\n")); + ep->Send(json_run_a_gcode("G91\nG1 Z10 F600\nG90\nM84\n")); + break; + + default: + break; + } + unhomed_move_mode = 0; jump_to_move_pop_2 = false; page_to(TJC_PAGE_MOVE_POP_2); } @@ -855,6 +893,7 @@ void refresh_page_auto_finish() { } void refresh_page_auto_moving() { + send_cmd_txt(tty_fd, "t5", "(" + std::to_string(printer_heater_bed_temperature) + "/" + std::to_string(printer_heater_bed_target) + ")"); if (step_1 == true) { send_cmd_picc(tty_fd, "q0", "109"); send_cmd_pco(tty_fd, "t1", "65535"); @@ -1491,7 +1530,7 @@ void refresh_page_main() { // CLL 每次开机发送断电续打 if (open_reprint_asked == false) { - ep->Send(json_run_a_gcode("KINEMATIC_POSITION\n")); + check_print_interrupted(); open_reprint_asked = true; } } @@ -1696,26 +1735,32 @@ void move_home() { void move_x_decrease() { ep->Send(move(AXIS_X, "-" + std::to_string(printer_move_dist), 130)); + unhomed_move_mode = 2; } void move_x_increase() { ep->Send(move(AXIS_X, "+" + std::to_string(printer_move_dist), 130)); + unhomed_move_mode = 1; } void move_y_decrease() { ep->Send(move(AXIS_Y, "-" + std::to_string(printer_move_dist), 130)); + unhomed_move_mode = 4; } void move_y_increase() { ep->Send(move(AXIS_Y, "+" + std::to_string(printer_move_dist), 130)); + unhomed_move_mode = 3; } void move_z_decrease() { ep->Send(move(AXIS_Z, "-" + std::to_string(printer_move_dist), 10)); + unhomed_move_mode = 5; } void move_z_increase() { ep->Send(move(AXIS_Z, "+" + std::to_string(printer_move_dist), 10)); + unhomed_move_mode = 6; } bool get_filament_detected() { @@ -2115,7 +2160,7 @@ void go_to_network() { scan_ssid_and_show(); get_wlan0_status(); if (strcmp(status_result.wpa_state, "COMPLETED") == 0) { - current_connected_ssid_name = status_result.ssid; // 如果已经连接wifi，获取wifi的名字 + current_connected_ssid_name = hex_to_utf8(status_result.ssid); // 如果已经连接wifi，获取wifi的名字 } else if (strcmp(status_result.wpa_state, "INACTIVE")) { current_connected_ssid_name.clear(); // 如果没连接wifi，清除掉当前已连接wifi的名字 } @@ -2143,7 +2188,7 @@ void refresh_page_wifi_list() { if (0 == page_wifi_current_pages) { if (0 == i) { if (strcmp(status_result.wpa_state, "COMPLETED") == 0) { - send_cmd_txt(tty_fd, "t" + std::to_string(i+1), status_result.ssid); + send_cmd_txt(tty_fd, "t" + std::to_string(i+1), hex_to_utf8(status_result.ssid)); } else { send_cmd_txt(tty_fd, "t" + std::to_string(i+1), page_wifi_ssid_list[i]); } @@ -2496,7 +2541,10 @@ void level_mode_printing_print_file() { } void update_finished_tips() { - page_to(TJC_PAGE_UPDATE_FINISH); + // page_to(TJC_PAGE_UPDATE_FINISH); + sleep(5); + system("sync"); + system("systemctl restart makerbase-client.service"); } bool get_mks_oobe_enabled() { @@ -2885,6 +2933,7 @@ void bed_calibrate() { if (manual_count == 4) { bed_offset = 0; printer_idle_timeout_state = "Printing"; + ep->Send(json_run_a_gcode("ABORT\n")); ep->Send(json_run_a_gcode("M4030")); page_to(TJC_PAGE_BED_MOVING); }else if (manual_count == 3) { @@ -3055,7 +3104,7 @@ void print_log() { system("bash -c 'cp /home/mks/klipper_logs/auto_update.log* /home/mks/gcode_files/sda1/QD_Log/'"); system("bash -c 'cp /root/frp/frpc.log* /home/mks/gcode_files/sda1/QD_Log/'"); system("bash -c 'cp /root/frp/frpc.*.log /home/mks/gcode_files/sda1/QD_Log/'"); - system("cp /root/frp/frpc.toml /home/mks/gcode_files/sda1/QD_Log/frpc.toml"); + system("cp /root/frp/frpc.toml /home/mks/gcode_files/sda1/QD_Log/server.cfg"); page_to(TJC_PAGE_PRINT_LOG_S); } } @@ -3228,16 +3277,15 @@ void go_to_showqr() { page_to(TJC_PAGE_SHOW_QR); if (strcmp(status_result.wpa_state, "COMPLETED") == 0 || mks_ethernet) { if (qr_refreshed == false) { + send_cmd_cp_close(tty_fd, "cp0"); if (open_qr_refreshed == true || access("/home/mks/qrcode/qrcode.jpg", F_OK) == -1) qrmessage = run_python_code("python3 /home/mks/qrcode/qrcode_QD.py 176\n"); std::cout << "qrmessage:" << qrmessage << std::endl; if (qrmessage.find("Missing or invalid") != -1) { send_cmd_txt(tty_fd, "t4", qrmessage); send_cmd_vis(tty_fd, "t4", "1"); - send_cmd_cp_close(tty_fd, "cp0"); } else if (qrmessage.find("No") != -1) { send_cmd_vis(tty_fd, "t4", "1"); - send_cmd_cp_close(tty_fd, "cp0"); } else { open_qr_refreshed = true; refresh_files_list_picture("/home/mks/qrcode/qrcode.jpg", 176, 0); @@ -3295,7 +3343,12 @@ void update_server(int choice) { // CLL 连接服务器获取json文件 if (choice == 0) { - system("curl -s -S -L -o /root/frp/server_list.json http://www.aws.qidi3dprinter.com:5050/downloads/server_list.json"); + // system("curl -s -S -L -o /root/frp/server_list.json http://www.aws.qidi3dprinter.com:5050/downloads/server_list.json"); + get_mks_selected_server(); + std::string server_for_command = selected_server.empty() ? "aws" : selected_server; + std::string command = "curl -s -S -L -o /root/frp/server_list.json http://www." + server_for_command + ".qidi3dprinter.com:5050/downloads/server_list.json"; + std::cout << "Executing command: " << command << std::endl; + system(command.c_str()); } else { qr_refreshed = false; // CLL 当choice不为0时，该函数用于切换服务器，需要重新刷新二维码 } @@ -3468,7 +3521,7 @@ void check_online_version() { page_to(TJC_PAGE_SEARCH_SERVER); if (connection_method == 0) return; - target_soc_version = run_python_code("python3 /root/auto_update/version_check_Q1.py"); + target_soc_version = run_python_code("python3 /root/auto_update/version_check.py"); std::cout << "服务器版本:" << target_soc_version << std::endl; if (target_soc_version.find("0") == 0) { page_to(TJC_PAGE_UPDATE_MODE); @@ -3520,7 +3573,7 @@ void online_update() { pthread_t recevice_progress_pthread; pthread_create(&recevice_progress_pthread, NULL, recevice_progress_handle, NULL); system("rm /home/mks/gcode_files/.cache/*\n"); - system("python3 /root/auto_update/download_update_Q1.py\n"); + system("python3 /root/auto_update/download_update.py\n"); // page_to(TJC_PAGE_UPDATE_FINISH); system("sync\n"); system("systemctl restart makerbase-client\n"); @@ -3582,4 +3635,38 @@ void set_mks_ethernet(int target) { mksini_save(); mksini_free(); mks_ethernet = target; +} + +std::string hex_to_utf8(const std::string& hex) { + std::ostringstream utf8; + size_t i = 0; + while (i < hex.size()) { + if (i + 3 < hex.size() && hex[i] == '\\' && hex[i + 1] == 'x') { + std::string hex_byte = hex.substr(i + 2, 2); + int value; + std::istringstream(hex_byte) >> std::hex >> value; + utf8 << static_cast(value); + i += 4; + } else { + utf8 << hex[i++]; + } + } + return utf8.str(); +} + +void check_print_interrupted() { + std::ifstream infile("/home/mks/klipper_config/saved_variables.cfg"); + if (!infile) { + std::cerr << "无法打开文件 " << "/home/mks/klipper_config/saved_variables.cfg" << std::endl; + return; + } + std::stringstream buffer; + buffer << infile.rdbuf(); + std::string printer_variables = buffer.str(); + infile.close(); + std::string print_interrupted_status = printer_variables.substr(printer_variables.find("was_interrupted =") + 18, 5); + if (print_interrupted_status != "False") { + ep->Send(json_run_a_gcode("DETECT_INTERRUPTION\n")); + jump_to_resume_print = true; + } } \ No newline at end of file diff --git a/src/mks_gcode.cpp b/src/mks_gcode.cpp index 0acc434..c3fa826 100644 --- a/src/mks_gcode.cpp +++ b/src/mks_gcode.cpp @@ -234,7 +234,7 @@ void parse_gcode_response(nlohmann::json params) { step_2 = true; } } else if (params0.find("echo: Detected unexpected interruption during the last print.") != -1 || params0.find("echo: Yes: RESUME_INTERRUPTED") != -1 || params0.find("echo: No: CLEAR_LAST_FILE") != -1) { - jump_to_resume_print = true; + // jump_to_resume_print = true; } } } diff --git a/src/mks_update.cpp b/src/mks_update.cpp index e2560a3..5fe3ac2 100644 --- a/src/mks_update.cpp +++ b/src/mks_update.cpp @@ -416,6 +416,8 @@ void start_update() system("systemctl stop moonraker.service\n"); system("find /home/mks/gcode_files -maxdepth 1 -type d ! -name sd* -a ! -name '.*' | grep gcode_files/ | xargs rm -rf"); system("cp /home/mks/gcode_files/sda1/QD_Update/QD_gcode/*.gcode /home/mks/gcode_files; chmod 777 /home/mks/gcode_files/*.gcode; sync"); + sleep(3); + system("systemctl restart moonraker.service\n"); } // 检测到UI文件 @@ -435,8 +437,7 @@ void start_update() if (!factory_mode) { command += "mv " + filePath + " " + filePath + ".bak; "; - } - + } command += "sync"; system(command.c_str()); break; // 每次更新只处理一个UI文件 @@ -460,7 +461,7 @@ void start_update() { std::string filename = entry->d_name; if (filename.rfind(".bak") != std::string::npos) continue; - if (filename.find("QD_Q1_PATCH") == 0 || filename.find("QD_Q1_SOC") == 0 || filename.find("QD_Mate3_SOC") == 0) + if (filename.find("QD_Q1_PATCH") == 0 || filename.find("QD_Q1_SOC") == 0 || filename.find("QD_Mates3_SOC") == 0) { std::string file_path = base_path + filename; std::string command = "mv " + file_path + " " + base_path + "mks.deb; dpkg -i --force-overwrite " + base_path + "mks.deb;"; @@ -472,7 +473,6 @@ void start_update() { new_file_name += ".bak"; } - command = "mv " + base_path + "mks.deb " + new_file_name + "; sync"; system(command.c_str()); } diff --git a/src/ui.cpp b/src/ui.cpp index c5903f0..d9a2058 100644 --- a/src/ui.cpp +++ b/src/ui.cpp @@ -104,6 +104,8 @@ extern bool mks_file_parse_finished; extern int printer_extruder_temperature; extern int printer_extruder_target; +extern int printer_heater_bed_target; + extern std::string printer_webhooks_state; extern bool printer_ready; @@ -642,18 +644,30 @@ void tjc_event_clicked_handler(int page_id, int widget_id, int type_id) { switch (widget_id) { case TJC_PAGE_ALL_TO_MAIN: - page_to(TJC_PAGE_MAIN); + if (printer_print_stats_state == "printing" || printer_print_stats_state == "paused") { + page_to(TJC_PAGE_PRINTING); + jump_to_print = false; + } else + page_to(TJC_PAGE_MAIN); break; case TJC_PAGE_ALL_TO_FILE_LIST: break; case TJC_PAGE_ALL_TO_ADJUST: - go_to_adjust(); + if (printer_print_stats_state == "printing" || printer_print_stats_state == "paused") { + page_to(TJC_PAGE_PRINTING); + jump_to_print = false; + } else + go_to_adjust(); break; case TJC_PAGE_ALL_TO_SETTING: - go_to_setting(); + if (printer_print_stats_state == "printing" || printer_print_stats_state == "paused") { + page_to(TJC_PAGE_PRINTING); + jump_to_print = false; + } else + go_to_setting(); break; case TJC_PAGE_PREVIEW_BACK: @@ -699,6 +713,11 @@ void tjc_event_clicked_handler(int page_id, int widget_id, int type_id) { break; case TJC_PAGE_PREVIEW_BED_LEVELING: + if (printer_print_stats_state == "printing" || printer_print_stats_state == "paused") { + page_to(TJC_PAGE_PRINTING); + jump_to_print = false; + break; + } if (printer_bed_leveling == true) { printer_bed_leveling = false; }else { @@ -1369,8 +1388,7 @@ void tjc_event_clicked_handler(int page_id, int widget_id, int type_id) { break; case TJC_PAGE_LEVEL_MODE_BED_CALIBRATION: - manual_count = 4; - bed_calibrate(); + page_to(TJC_PAGE_CALIBRATE_WARNING); break; case TJC_PAGE_LEVEL_MODE_TO_COMMON_SETTING: @@ -1419,6 +1437,10 @@ void tjc_event_clicked_handler(int page_id, int widget_id, int type_id) { break; case TJC_PAGE_AUTO_HEATERBED_NEXT: + if (printer_heater_bed_target < 35) { + page_to(TJC_PAGE_AUTO_WARNING); + break; + } auto_level_button_enabled = true; printer_idle_timeout_state = "Printing"; start_auto_level(); @@ -2070,7 +2092,7 @@ void tjc_event_clicked_handler(int page_id, int widget_id, int type_id) { case TJC_PAGE_RESUME_PRINT: switch(widget_id) { case TJC_PAGE_RESUME_PRINT_YES: - page_to(TJC_PAGE_MAIN); + page_to(TJC_PAGE_RE_PRINTING); send_gcode("RESUME_INTERRUPTED\n"); break; @@ -2346,6 +2368,35 @@ void tjc_event_clicked_handler(int page_id, int widget_id, int type_id) { } break; + case TJC_PAGE_AUTO_WARNING: + switch (widget_id) + { + case TJC_PAGE_AUTO_WARNING_YES: + page_to(TJC_PAGE_AUTO_HEATERBED); + break; + + default: + break; + } + break; + + case TJC_PAGE_CALIBRATE_WARNING: + switch (widget_id) + { + case TJC_PAGE_CALIBRATE_WARNING_NEXT: + manual_count = 4; + bed_calibrate(); + break; + + case TJC_PAGE_CALIBRATE_WARNING_BACK: + page_to(TJC_PAGE_LEVEL_MODE); + break; + + default: + break; + } + break; + default: break; }