update V1.6.0

README.md

@@ -9,11 +9,20 @@ QIDI PLUS4 is a 3D printer that uses Klipper as its foundation. This repository
 
 For convenience, QIDI provides version-specific packaged files. Please download the necessary compressed package file prefixed with "PLUS4." Select the appropriate branch for download, with each branch name reflecting the corresponding version.
 
-## V1.4.3 Update Content
+## V1.6.0 Update Content
 
 **Note:** After updating, the Klipper configuration file will be replaced. The previous configuration file will be backed up as `printer_{datetime}.cfg`, printer recalibration will be required.
 
-1.Optimize the execution logic of chamber heating.
+1. Added network testing functionality.
+2. Added support for AX300 and AX600 Wi-Fi adapters.
+3. Optimized chamber heating logic: chamber heating starts only when the heated bed reaches the specified temperature.
+4. Added temperature limits and reminders (chamber, heated bed, nozzle) on the Fluidd page.
+5. Fixed an issue where disconnection caused online updates to crash.
+6. Fixed the problem of losing settings after rebooting following a language switch.
+7. Enhanced support for LAN mode.
+
+
+## The online update version will be uploaded later. If you have already updated this version earlier, please ignore the online update prompt.
 
 
 ## Detailed update process

config/gcode_macro.cfg

@@ -1,4 +1,9 @@
-# QIDI Plus4 V1.0.0
+# QIDI Plus4 V1.6.0
+#20241102 
+#1. 起始代码腔室加热将在调平后开启
+#2. 腔室加热开启必须带着热床升温
+#3. M141和M191宏定义修改，热床低于70会开启热床加热
+#4. 擦料时取消打印，会先移动一点出来
 
 [gcode_macro _CG28]
 gcode:
@@ -215,12 +220,12 @@ gcode:
     M106 P3 S0
     M106 S255
     G28      
-    M141 S{chambertemp}    
+    M141 S0
     M140 S{bedtemp}    
     M106 S0
     CLEAR_NOZZLE HOTEND={hotendtemp}
-    M191 S{chambertemp}    
     M190 S{bedtemp}     
+#    M141 S{chambertemp}    
     M104 S140
     G29
     G0 Z50 F600
@@ -416,7 +421,9 @@ gcode:
     {% if (printer.gcode_move.position.z) < 200 %}
         G1 Z200 F600                                      
     {% endif %}
-
+    {% if (printer.gcode_move.position.y) > 300 %}
+        G1 Y250 F6000
+    {% endif %}
     G1  X0 Y0 F7800
     save_zoffset
     SET_IDLE_TIMEOUT TIMEOUT={printer.configfile.settings.idle_timeout.timeout}
@@ -560,13 +567,20 @@ gcode:
         {% endfor %}
     {% endif %}
 
+
+
 [gcode_macro M141]
 gcode:
     {% if printer["heater_generic chamber"] is defined %}
         {% set s = params.S|float %}
         SET_HEATER_TEMPERATURE HEATER=chamber TARGET={([s, 65]|min)}
+        # {% if printer['heater_bed'].target < s+25 and s!=0 %}
+        #     M140 S{s+25}
+        #     M118 If the heatbed is below {s+25} degrees, the heatbed temperature will be automatically set to {s+25}.
+        # {% endif %}
     {% endif %}
 
+
 [gcode_macro M191]
 gcode:
     {% if printer["heater_generic chamber"] is defined %}
@@ -880,6 +894,9 @@ variable_k:1
 gcode:
     {% set temp = printer["heater_generic chamber"].target %}
     M141 S0
+    {% if temp > 0 %}
+        G4 P15000
+    {% endif %}
     BED_MESH_CLEAR
     {% if k|int==1 %}
         G28   
@@ -897,8 +914,19 @@ gcode:
     {% else %}
         g28
         get_zoffset
-        BED_MESH_PROFILE LOAD=default
+        {% if printer["bed_mesh"].profiles.default %}
-        SAVE_VARIABLE VARIABLE=profile_name VALUE='"default"'
+            BED_MESH_PROFILE LOAD=default
+            SAVE_VARIABLE VARIABLE=profile_name VALUE='"default"'
+        {% else %}
+            G1 X{150 - printer.probe["x_offset"]} Y{150 - printer.probe["y_offset"]} F9000
+            G1 Z10 F600
+            probe
+            SAVE_Z_OFFSET_TO_BED_MESH
+            G1 z10 F600
+            _BED_MESH_CALIBRATE PROFILE=default
+            G4 P5000
+            SAVE_CONFIG_QD
+        {% endif %}
     {% endif %}
 
 [gcode_macro M204]

config/printer.cfg

@@ -275,6 +275,10 @@ pid_Kd=749.125
 
 min_temp:-100
 max_temp:70
+target_min_temp:45
+target_max_temp:65
+heat_with_heater_bed:True
+heat_with_heater_bed_tem_add:25
 
 [verify_heater chamber]
 max_error: 400