QIDI Studio - en to en translation catalogue (321 entries)

en: 
    
    Would you like to redirect to the webpage for rating?
en: 
    
    Would you like to redirect to the webpage to give a rating?

en: 
    You can discard the preset values you have modified, or choose to continue using the modified values in the new project
en: 
    You can discard the preset values you have modified or choose to continue using the modified values in the new project

en: 
    You can save or discard the preset values you have modified, or choose to continue using the values you have modified on the new preset.
en: 
    You can save or discard the preset values you have modified, or you can choose to continue using the values you have modified on the new preset.

en:  can not be opened
en:  cannot be opened

en:  is too close to exclusion area, and collisions will be caused.
en:  is too close to an exclusion area, and collisions will be caused.

en: A G-code path goes beyond the boundary of plate.
en: A G-code path goes beyond plate boundaries.

en: A config exists with the same name: %s, do you want to override it.
en: A config exists with the same name: %s; do you want to replace it?

en: A file exists with the same name: %s, do you want to override it.
en: A file exists with the same name: %s; do you want to replace it?

en: AMS filament backup is not enabled, please enable it in the AMS settings.
en: AMS filament backup is not enabled; please enable it in the AMS settings.

en: AMS filaments
en: AMS filament

en: Acceleration of initial layer. Using a lower value can improve build plate adhensive
en: Acceleration of initial layer. Using a lower value can improve build plate adhesion.

en: Acceleration of top surface infill. Using a lower value may improve top surface quality
en: This is the acceleration of top surface infill. Using a lower value may improve top surface quality.

en: Add plate
en: Add Plate

en: Advance
en: Advanced

en: All the selected objects are on the locked plate,
    We can not do auto-orient on these objects.
en: All the selected objects are on a locked plate,
    We cannot auto-orient these objects.

en: Ams Status
en: AMS Status

en: An SD card needs to be inserted before printing via LAN.
en: A MicroSD card needs to be inserted before printing via LAN.

en: An SD card needs to be inserted before printing.
en: A MicroSD card needs to be inserted before printing.

en: An SD card needs to be inserted before send to printer SD card.
en: A Micro SD card needs to be inserted before sending to printer SD card.

en: An SD card needs to be inserted before sending to printer.
en: A MicroSD card needs to be inserted before sending to printer.

en: An SD card needs to be inserted to record timelapse.
en: A Micro SD card needs to be inserted to record timelapse.

en: An error occurred. Maybe memory of system is not enough or it's a bug of the program
en: An error occurred. System memory may not be enough or it may be a program bug.

en: An object is layed over the boundary of plate.
en: An object is laid over the boundary of the plate.

en: Are you sure to %1% the selected preset?
en: Are you sure you want to %1% the selected preset?

en: Assemble the selected objects to an object with multiple parts
en: Assemble the selected objects into an object with multiple parts

en: Assemble the selected objects to an object with single part
en: Assemble the selected objects into an object that is a single part

en: At least one successful print record of this print profile is required 
    to give a positive rating(4 or 5stars).
en: At least one successful print record of this print profile is required 
    to give a positive rating (4 or 5 stars).

en: Auto Flow Rate Calibration utilizes QIDI TECH's Micro-Lidar technology, directly measuring the calibration patterns. However, please be advised that the efficacy and accuracy of this method may be compromised with specific types of materials. Particularly, filaments that are transparent or semi-transparent, sparkling-particled, or have a high-reflective finish may not be suitable for this calibration and can produce less-than-desirable results.
    
    The calibration results may vary between each calibration or filament. We are still improving the accuracy and compatibility of this calibration through firmware updates over time.
    
    Caution: Flow Rate Calibration is an advanced process, to be attempted only by those who fully understand its purpose and implications. Incorrect usage can lead to sub-par prints or printer damage. Please make sure to carefully read and understand the process before doing it.
en: Auto Flow Rate Calibration utilizes QIDI TECH's Micro-Lidar technology, directly measuring the calibration patterns. However, please be advised that the efficacy and accuracy of this method may be compromised with specific types of materials. Particularly, filaments that are transparent or semi-transparent, have sparkles, or have a highly-reflective finish may not be suitable for this calibration and can produce less-than-desirable results.
    
    The calibration results may vary between each calibration or filament. We are still improving the accuracy and compatibility of this calibration through firmware updates over time.
    
    Caution: Flow Rate Calibration is an advanced process, to be attempted only by those who fully understand its purpose and implications. Incorrect usage can lead to sub-par prints or printer damage. Please make sure to carefully read and understand the process before doing it.

en: Auto orient
en: Auto Orient

en: Auto sync user presets(Printer/Filament/Process)
en: Auto sync user presets (Printer/Filament/Process)

en: Auto-recovery from step loss
en: Auto-recover from step loss

en: Avoid warping
    Did you know that when printing materials that are prone to warping such as ABS, appropriately increasing the heatbed temperature can reduce the probability of warping.
en: Avoid warping
    Did you know that when printing materials that are prone to warping such as ABS, appropriately increasing the heatbed temperature can reduce the probability of warping?

en: Bambu Studio is based on PrusaSlicer by Prusa Research, which is from Slic3r by Alessandro Ranellucci and the RepRap community
en: Bambu Studio is based on PrusaSlicer by Prusa Research, which is based on Slic3r by Alessandro Ranellucci and the RepRap community

en: Bed Type
en: Plate Type

en: Bed adhension
en: Bed adhesion

en: Bed temperature for layers except the initial one. Value 0 means the filament does not support to print on the Cool Plate
en: This is the bed temperature for layers except for the first one. A value of 0 means the filament does not support printing on the Cool Plate.

en: Bed temperature for layers except the initial one. Value 0 means the filament does not support to print on the Engineering Plate
en: This is the bed temperature for layers except for the first one. A value of 0 means the filament does not support printing on the Engineering Plate.

en: Bed temperature for layers except the initial one. Value 0 means the filament does not support to print on the High Temp Plate
en: This is the bed temperature for layers except for the first one. A value of 0 means the filament does not support printing on the High Temp Plate.

en: Bed temperature of the initial layer. Value 0 means the filament does not support to print on the Cool Plate
en: This is the bed temperature of the first layer. A value of 0 means the filament does not support printing on the Cool Plate.

en: Bed temperature of the initial layer. Value 0 means the filament does not support to print on the Engineering Plate
en: This is the bed temperature of the first layer. A value of 0 means the filament does not support printing on the Engineering Plate.

en: Bed temperature of the initial layer. Value 0 means the filament does not support to print on the High Temp Plate
en: This is the bed temperature of the first layer. A value of 0 means the filament does not support printing on the High Temp Plate.

en: Bed temperature when cool plate is installed. Value 0 means the filament does not support to print on the Cool Plate
en: This is the bed temperature when the cool plate is installed. A value of 0 means the filament does not support printing on the Cool Plate.

en: Bed temperature when engineering plate is installed. Value 0 means the filament does not support to print on the Engineering Plate
en: This is the bed temperature when the engineering plate is installed. A value of 0 means the filament does not support printing on the Engineering Plate.

en: Bed type
en: Plate type

en: Bed types supported by the printer
en: Plate types supported by the printer

en: Calibrating the micro lida
en: Calibrating the micro lidar

en: Can not add models when in preview mode!
en: Unable to add models in preview mode

en: Can not print multiple filaments which have large difference of temperature together. Otherwise, the extruder and nozzle may be blocked or damaged during printing
en: Unable to print multiple filaments which have large temperature differences together. Otherwise, the extruder and nozzle may be blocked or damaged during printing.

en: Can't apply when process preview.
en: Can't apply when processing preview

en: Can't start this without SD card.
en: Can't start this without a Micro SD card.

en: Cannot send the print task when the upgrade is in progress
en: Cannot send print tasks when an update is in progress

en: Change these settings automatically? 
    Yes - Change these settings and enable spiral mode automatically
    No  - Give up using spiral mode this time
en: Change these settings automatically? 
    Yes - Change these settings and enable spiral/vase mode automatically
    No  - Cancel enabling spiral mode

en: Changing the region will log out your account.
en: Changing the region will log you out of your account.

en: Check for Update
en: Check for Updates

en: Choose an AMS slot then press "Load" or "Unload" button to automatically load or unload filaments.
en: Choose an AMS slot then press "Load" or "Unload" button to automatically load or unload filament.

en: Click the icon to edit color painting of the object
en: Click the icon to edit color painting for the object

en: Click the icon to toggle printable property of the object
en: Click the icon to toggle printable properties of the object

en: Click to drop current modify and reset to saved value.
en: Click to drop current modifications and reset to saved value.

en: Click to pick filament color
en: Click to select filament color

en: Close all cooling fan for the first certain layers. Cooling fan of the first layer used to be closed to get better build plate adhesion
en: Turn off all cooling fans for the first few layers. This can be used to improve bed adhesion.

en: Color painting
en: Color Painting

en: Colour
en: Color

en: Comfirm Save As
en: Confirm Save As

en: Compared with the default profile of 0.2 mm nozzle, it has a smaller layer height, and results in minimal layer lines and higher printing quality, but shorter printing time.
en: Compared with the default profile of 0.2 mm nozzle, it has a smaller layer height. This results in minimal layer lines and higher print quality but longer print time.

en: Compared with the default profile of a 0.2 mm nozzle, it has a bigger layer height, and results in slightly visible layer lines, but shorter printing time.
en: Compared with the default profile of a 0.2 mm nozzle, it has a bigger layer height. This results in slightly visible layer lines but shorter print time.

en: Compared with the default profile of a 0.2 mm nozzle, it has a slightly bigger layer height, and results in almost negligible layer lines, and slightly shorter printing time.
en: Compared with the default profile of a 0.2 mm nozzle, it has a slightly bigger layer height. This results in almost negligible layer lines and slightly longer print time.

en: Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer height, and results in almost invisible layer lines and higher printing quality, but shorter printing time.
en: Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer height. This results in almost invisible layer lines and higher print quality but longer print time.

en: Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer lines, lower speeds and acceleration, and the sparse infill pattern is Gyroid. So, it results in almost invisible layer lines and much higher printing quality, but much longer printing time.
en: Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer lines, lower speeds and acceleration, and the sparse infill pattern is Gyroid. This results in almost invisible layer lines and much higher print quality but much longer print time.

en: Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer lines, lower speeds and acceleration, and the sparse infill pattern is Gyroid. So, it results in minimal layer lines and much higher printing quality, but much longer printing time.
en: Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer lines, lower speeds and acceleration, and the sparse infill pattern is Gyroid. This results in minimal layer lines and much higher print quality but much longer print time.

en: Compared with the default profile of a 0.2 mm nozzle, it has lower speeds and acceleration, and the sparse infill pattern is Gyroid. So, it results in much higher printing quality, but a much longer printing time.
en: Compared with the default profile of a 0.2 mm nozzle, it has lower speeds and acceleration, and the sparse infill pattern is Gyroid. This results in much higher print quality but a much longer print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a bigger layer height, and results in more apparent layer lines and lower printing quality, but shorter printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a bigger layer height. This results in more apparent layer lines and lower print quality but shorter print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a bigger layer height, and results in more apparent layer lines and lower printing quality, but slightly shorter printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a bigger layer height. This results in more apparent layer lines and lower print quality but slightly shorter print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, and results in almost negligible layer lines and higher printing quality, but longer printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height. This results in almost negligible layer lines and higher print quality but longer print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, and results in almost negligible layer lines and longer printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height. This results in almost negligible layer lines and longer print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, and results in less apparent layer lines and higher printing quality, but longer printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height. This results in less apparent layer lines and higher print quality but longer print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, lower speeds and acceleration, and the sparse infill pattern is Gyroid. So, it results in almost negligible layer lines and much higher printing quality, but much longer printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, lower speeds and acceleration, and the sparse infill pattern is Gyroid. This results in almost negligible layer lines and much higher print quality but much longer print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, lower speeds and acceleration, and the sparse infill pattern is Gyroid. So, it results in less apparent layer lines and much higher printing quality, but much longer printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, lower speeds and acceleration, and the sparse infill pattern is Gyroid. This results in less apparent layer lines and much higher print quality but much longer print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has more wall loops and a higher sparse infill density. So, it results in higher strength of the prints, but more filament consumption and longer printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has more wall loops and a higher sparse infill density. This results in higher print strength but more filament consumption and longer print time.

en: Compared with the default profile of a 0.6 mm nozzle, it has a bigger layer height, and results in more apparent layer lines and lower printing quality, but shorter printing time in some printing cases.
en: Compared with the default profile of a 0.6 mm nozzle, it has a bigger layer height. This results in more apparent layer lines and lower print quality but shorter print time in some cases.

en: Compared with the default profile of a 0.6 mm nozzle, it has a bigger layer height, and results in much more apparent layer lines and much lower printing quality, but shorter printing time in some printing cases.
en: Compared with the default profile of a 0.6 mm nozzle, it has a bigger layer height. This results in much more apparent layer lines and much lower print quality, but shorter print time in some cases.

en: Compared with the default profile of a 0.6 mm nozzle, it has a smaller layer height, and results in less apparent layer lines and higher printing quality, but longer printing time.
en: Compared with the default profile of a 0.6 mm nozzle, it has a smaller layer height. This results in less apparent layer lines and higher print quality but longer print time.

en: Compared with the default profile of a 0.6 mm nozzle, it has a smaller layer height, and results in less apparent layer lines and slight higher printing quality, but longer printing time.
en: Compared with the default profile of a 0.6 mm nozzle, it has a smaller layer height. This results in less apparent layer lines and slightly higher print quality but longer print time.

en: Compared with the default profile of a 0.6 mm nozzle, it has more wall loops and a higher sparse infill density. So, it results in higher strength of the prints, but more filament consumption and longer printing time.
en: Compared with the default profile of a 0.6 mm nozzle, it has more wall loops and a higher sparse infill density. This results in higher print strength but more filament consumption and longer print time.

en: Compared with the default profile of a 0.8 mm nozzle, it has a bigger layer height, and results in very apparent layer lines and much lower printing quality, but shorter printing time in some printing cases.
en: Compared with the default profile of a 0.8 mm nozzle, it has a bigger layer height. This results in very apparent layer lines and much lower print quality but shorter print time in some cases.

en: Compared with the default profile of a 0.8 mm nozzle, it has a much bigger layer height, and results in extremely apparent layer lines and much lower printing quality, but much shorter printing time in some printing cases.
en: Compared with the default profile of a 0.8 mm nozzle, it has a much bigger layer height. This results in extremely apparent layer lines and much lower print quality but much shorter print time in some cases.

en: Compared with the default profile of a 0.8 mm nozzle, it has a slightly smaller layer height, and results in slightly less but still apparent layer lines and slightly higher printing quality, but longer printing time in some printing cases.
en: Compared with the default profile of a 0.8 mm nozzle, it has a slightly smaller layer height. This results in slightly less but still apparent layer lines and slightly higher print quality, but longer print time in some cases.

en: Compared with the default profile of a 0.8 mm nozzle, it has a smaller layer height, and results in less but still apparent layer lines and slightly higher printing quality, but longer printing time in some printing cases.
en: Compared with the default profile of a 0.8 mm nozzle, it has a smaller layer height. This results in less but still apparent layer lines and slightly higher print quality, but longer print time in some cases.

en: ConnectPrinter(LAN)
en: Connect Printer (LAN)

en: Connection to AstroBox works correctly.
en: Connection to AstroBox is working correctly.

en: Connection to Duet works correctly.
en: Connection to Duet is working correctly.

en: Connection to FlashAir works correctly and upload is enabled.
en: Connection to FlashAir is working correctly and upload is enabled.

en: Connection to MKS works correctly.
en: Connection to MKS is working correctly.

en: Connection to OctoPrint works correctly.
en: Connection to OctoPrint is working correctly.

en: Connection to Prusa SL1 / SL1S works correctly.
en: Connection to Prusa SL1 / SL1S is working correctly.

en: Connection to PrusaLink works correctly.
en: Connection to PrusaLink is working correctly.

en: Connection to Repetier works correctly.
en: Connection to Repetier is working correctly.

en: Create Filament Successful
en: Filament Created Successfully

en: Current chamber temperature is higher than the material's safe temperature,it may result in material softening and clogging.The maximum safe temperature for the material is %d
en: Current chamber temperature is higher than the material's safe temperature; this may result in material softening and nozzle clogs.The maximum safe temperature for the material is %d

en: Custom vendor is not input, please input custom vendor.
en: Custom vendor missing; please input custom vendor.

en: Detect overhang wall
en: Detect overhang walls

en: Detour and avoid traveling across wall which may cause blob on surface
en: Detour and avoid traveling across walls to avoid the possibility of creating blobs on surfaces

en: Do you want to replace it
en: Do you want to replace it?

en: Don't support the whole bridge area which makes support very large. Bridge usually can be printing directly without support if not very long
en: Don't support the whole bridge area in order to use less support. Shorter bridges can usually be printed directly without support.

en: Download failed, File size exception.
en: Download failed; File size exception.

en: Download failed, unknown file format.
en: Download failed; unknown file format.

en: Embeded
    depth
en: Embedded
    depth

en: Enable this option if machine has auxiliary part cooling fan
en: Enable this option if the machine has an auxiliary part cooling fan

en: Enable this option to optimize part cooling fan speed for overhang and bridge to get better cooling
en: Enable this option to optimize the part cooling fan speed for overhangs and bridges to get better cooling

en: Enable this option to slow printing down for different overhang degree
en: Enable this option to slow down when printing overhangs. The speeds for different overhang percentages are set below.

en: Enable this option to slow printing speed down to make the final layer time not shorter than the layer time threshold in "Max fan speed threshold", so that layer can be cooled for a longer time. This can improve the cooling quality for needle and small details
en: Enable this option to slow printing speed down to make the final layer time not shorter than the layer time threshold in "Max fan speed threshold" so that the layer can be cooled for more time. This can improve the quality for fine details

en: Enable this to get a G-code file which has G2 and G3 moves. And the fitting tolerance is the same as resolution
en: Enable this to get a G-code file which has G2 and G3 moves. The fitting tolerance is the same as resolution

en: Enqueued
en: Queued

en: Experimental feature.Retracting and cutting off the filament at a longer distance during changes to minimize purge.While this reduces flush significantly, it may also raise the risk of nozzle clogs or other printing problems.
en: Experimental feature: Retracting and cutting off the filament at a longer distance during changes to minimize purge.While this reduces flush significantly, it may also raise the risk of nozzle clogs or other printing problems.

en: Experimental feature.Retraction length before cutting off during filament change
en: Experimental feature. Retraction length before cutting off during filament change

en: Experimental feature: Retracting and cutting off the filament at a greater distance during filament changes to minimize flush.Although it can notably reduce flush,  it may also elevate the risk of nozzle clogs or other printing complications.
en: Experimental feature: Retracting and cutting off the filament at a greater distance during filament changes to minimize flush. Although it can notably reduce flush,  it may also elevate the risk of nozzle clogs or other printing complications.

en: Experimental feature: Retracting and cutting off the filament at a greater distance during filament changes to minimize flush.Although it can notably reduce flush, it may also elevate the risk of nozzle clogs or other printing complications.Please use with the latest printer firmware.
en: Experimental feature: Retracting and cutting off the filament at a greater distance during filament changes to minimize flush. Although it can notably reduce flush, it may also elevate the risk of nozzle clogs or other printing complications. Please use with the latest printer firmware.

en: Extruders count
en: Extruder count

en: Failed to generate gcode for invalid custom G-code.
en: Failed to generate G-code for invalid custom G-code.

en: Failed to save gcode file.
    Error message: %1%.
    Source file %2%.
en: Failed to save G-code file.
    Error message: %1%.
    Source file %2%.

en: Fan speed for overhang
en: Fan speed for overhangs

en: Fatal error, exception caught: %1%
en: Fatal error; exception caught: %1%

en: Featue 1
en: Feature 1

en: Fetching model infomations ...
en: Fetching model information ...

en: Filament Tangle Detect
en: Filament Tangle Detection

en: Filament count exceeds the maximum number that painting tool supports. only the first %1% filaments will be available in painting tool.
en: Filament count exceeds the maximum number that painting tool supports. Only the first %1% filaments will be available in painting tool.

en: Filament serial is not inputed, please input serial.
en: Filament serial missing; please input serial.

en: Flushing volumes: Auto-calculate every time when the color is changed.
en: Flushing volumes: Auto-calculate every time the color is changed.

en: Flushing volumes: Auto-calculate every time when the filament is changed.
en: Flushing volumes: Auto-calculate every time the filament is changed.

en: Following line %s contains reserved keywords.
    Please remove it, or will beat G-code visualization and printing time estimation. | Following lines %s contain reserved keywords.
    Please remove them, or will beat G-code visualization and printing time estimation.
en[0]: Following line %s contains reserved keywords.
    Please remove it, or G-code visualization and print time estimation will be broken.
en[1]: Following lines %s contain reserved keywords.
    Please remove them, or G-code visualization and print time estimation will be broken.

en: Following model object has been repaired | Following model objects have been repaired
en[0]: The following model object has been repaired
en[1]: The following model objects have been repaired

en: Following preset will be deleted too. | Following presets will be deleted too.
en[0]: The following preset will be deleted too:
en[1]: The following presets will be deleted too:

en: For more information, please check out Wiki
en: For more information, please check out our Wiki

en: Force cooling for overhang and bridge
en: Force cooling for overhangs and bridges

en: Force part cooling fan to be at this speed when printing bridge or overhang wall which has large overhang degree. Forcing cooling for overhang and bridge can get better quality for these part
en: Force part cooling fan to be at this speed when printing bridges or overhang walls which have a large overhang degree. Forcing cooling for overhangs and bridges can improve quality for these parts.

en: Found following keys unrecognized:
en: The following unrecognized keys have been found:

en: G-code path is generated after simplifying the contour of model to avoid too many points and gcode lines in the gcode file. Smaller value means higher resolution and more time to slice
en: G-code path is generated after simplifying the contour of model to avoid too many points and g-code lines in the g-code file. Smaller values mean higher resolution and longer slicing times.

en: Get ticket from device timeout
en: Timeout getting ticket from device

en: Height of initial layer. Making initial layer height thick slightly can improve build plate adhension
en: Height of initial layer. Making initial layer height slightly thicker can improve build plate adhesion.

en: Higher chamber temperature can help suppress or reduce warping and potentially lead to higher interlayer bonding strength for high temperature materials like ABS, ASA, PC, PA and so on.At the same time, the air filtration of ABS and ASA will get worse.While for PLA, PETG, TPU, PVA and other low temperature materials,the actual chamber temperature should not be high to avoid cloggings, so 0 which stands for turning off is highly recommended
en: Higher chamber temperature can help suppress or reduce warping and potentially lead to higher interlayer bonding strength for high temperature materials like ABS, ASA, PC, PA and so on. At the same time, the air filtration of ABS and ASA will get worse.While for PLA, PETG, TPU, PVA and other low temperature materials, the actual chamber temperature should not be high to avoid clogs, so 0 (turned off) is highly recommended.

en: How to use calibration result?
en: How can I use calibration results?

en: How to use keyboard shortcuts
    Did you know that QIDI Studio offers a wide range of keyboard shortcuts and 3D scene operations.
en: How to use keyboard shortcuts
    Did you know that QIDI Studio offers a wide range of keyboard shortcuts and 3D scene operations?

en: If enable this setting, part cooling fan will never be stopped and will run at least at minimum speed to reduce the frequency of starting and stopping
en: Enabling this setting means that the part cooling fan will run continuously at minimum speed instead of stopping to reduce the frequency of starting and stopping.

en: If enabled, auto-calculate every time when filament is changed
en: If enabled, auto-calculate every time filament is changed

en: If there are two identical filaments in AMS, AMS filament backup will be enabled. 
    (Currently supporting automatic supply of consumables with the same brand, material type, and color)
en: If there are two identical filaments in an AMS, AMS filament backup will be enabled. 
    (This currently supports automatic supply of consumables with the same brand, material type, and color)

en: InFo
en: Info

en: It has a general layer height, and results in general layer lines and printing quality. It is suitable for most general printing cases.
en: It has a normal layer height, and results in average layer lines and print quality. It is suitable for most printing cases.

en: It has a small layer height, and results in almost negligible layer lines and high printing quality. It is suitable for most general printing cases.
en: It has a small layer height, and results in almost negligible layer lines and high print quality. It is suitable for most general printing cases.

en: It has a very big layer height, and results in very apparent layer lines, low printing quality and general printing time.
en: It has a very big layer height, and results in very apparent layer lines, low print quality and shorter printing time.

en: Lay on face
en: Lay on Face

en: Line width of initial layer
en: Line width of first layer

en: Line width of inner wall
en: Line width of inner walls

en: Loading G-codes
en: Loading G-code

en: Long retraction when cut(experimental)
en: Long retraction when cut (experimental)

en: Low temperature filament(PLA/PETG/TPU) is loaded in the extruder.In order to avoid extruder clogging,it is not allowed to set the chamber temperature above 45℃.
en: Low temperature filament (PLA/PETG/TPU) is loaded in the extruder. In order to avoid extruder clogging, it is not allowed to set the chamber temperature above 45℃.

en: Max length of bridges that don't need support. Set it to 0 if you want all bridges to be supported, and set it to a very large value if you don't want any bridges to be supported.
en: This is the maximum length of bridges that don't need support. Set it to 0 if you want all bridges to be supported, and set it to a very large value if you don't want any bridges to be supported.

en: Maximum detour distance for avoiding crossing wall. Don't detour if the detour distance is larger than this value. Detour length could be specified either as an absolute value or as percentage (for example 50%) of a direct travel path. Zero to disable
en: Maximum detour distance for avoiding crossing wall. Don't detour if the detour distance is larger than this value. Detour length could be specified either as an absolute value or as percentage (for example 50%) of a direct travel path. 0 disables this feature.

en: Maximum distance to move points in XY to try to achieve a smooth spiralIf expressed as a %, it will be computed over nozzle diameter
en: Maximum distance to move points in XY to try to achieve a smooth spiral. If expressed as a %, it will be computed over nozzle diameter

en: Maximum width of a segmented region. Zero disables this feature.
en: Maximum width of a segmented region. A value of 0 disables this feature.

en: Modified G-codes
en: Modified G-code

en: Modified Value(New)
en: Modified Value (New)

en: Move nozzle along the last extrusion path when retracting to clean leaked material on nozzle. This can minimize blob when printing new part after travel
en: Move nozzle along the last extrusion path when retracting to clean leaked material on nozzle. This can minimize blobs when printing new parts after traveling.

en: Move selection 10 mm in negative X direction
en: Move selection 10mm in negative X direction

en: Move selection 10 mm in negative Y direction
en: Move selection 10mm in negative Y direction

en: Move selection 10 mm in positive X direction
en: Move selection 10mm in positive X direction

en: Move selection 10 mm in positive Y direction
en: Move selection 10mm in positive Y direction

en: Movement step set to 1 mm
en: Movement step set to 1mm

en: No SD Card
en: No MicroSD Card

en: No warnings when loading 3MF with modified G-codes
en: No warnings when loading 3MF with modified G-code

en: Not apply
en: Not applied

en: Note: AstroBox version at least 1.1.0 is required.
en: Note: AstroBox version 1.1.0 or higher is required.

en: Note: OctoPrint version at least 1.1.0 is required.
en: Note: OctoPrint version 1.1.0 or higher is required.

en: Note: Repetier version at least 0.90.0 is required.
en: Note: Repetier version 0.90.0 or higher is required.

en: Nozzle may be blocked when the temperature is out of recommended range.
    Please confirm whether to use the temperature for printing.
en: Nozzle may be blocked when the temperature is out of recommended range.
    Please confirm in order to use the temperature for printing.

en: On OSX there is always only one instance of app running by default. However it is allowed to run multiple instances of same app from the command line. In such case this settings will allow only one instance.
en: On OSX there is always only one instance of app running by default. However it is allowed to run multiple instances of same app from the command line. In such case this setting will allow only one instance.

en: Only display printer names with changes to printer, filament, and process presets.
en: Only display printers with changes to printer, filament, and process presets are displayed.

en: Only one of the results with the same name will be saved. Are you sure you want to override the other results?
en: Only one of the results with the same name will be saved. Are you sure you want to replace the other results?

en: Order of wall/infill. false means print wall first.
en: Order of wall/infill. If this is unchecked, walls will be printed before infill.

en: Part cooling fan speed may be increased when auto cooling is enabled. This is the maximum speed limitation of part cooling fan
en: The part cooling fan speed may be increased when auto cooling is enabled. This is the maximum speed for the part cooling fan.

en: Part cooling fan speed will be max when the estimated layer time is shorter than the setting value
en: The part cooling fan will run at maximum speed when the estimated layer time is shorter than the threshold value.

en: Part cooling fan speed will start to run at min speed when the estimated layer time is no longer than the layer time in setting. When layer time is shorter than threshold, fan speed is interpolated between the minimum and maximum fan speed according to layer printing time
en: The part cooling fan will run at the minimum fan speed when the estimated layer time is longer than the threshold value. When the layer time is shorter than the threshold, the fan speed will be interpolated between the minimum and maximum fan speed according to layer printing time.

en: Part cooling fan will be enabled for layers of which estimated time is shorter than this value. Fan speed is interpolated between the minimum and maximum fan speeds according to layer printing time
en: The part cooling fan will be enabled for layers where the estimated time is shorter than this value. Fan speed is interpolated between the minimum and maximum fan speeds according to layer printing time.

en: Perform
en: Apply

en: Performed boolean intersection fails 
     because the selected parts have no intersection
en: Performing boolean intersection failed 
     because the selected parts have no intersection

en: Please add at least one more object and select them together,
    then right click to assembly these objects.
en: Please add at least one more object and select them together,
    then right click to assemble these objects.

en: Please change the desiccant when it is too wet. The indicator may not represent accurately in following cases : when the lid is open or the desiccant pack is changed. it take hours to absorb the moisture, low temperatures also slow down the process.
en: Please change the desiccant when it is too wet. The indicator may not represent accurately in following cases: when the lid is open or the desiccant pack is changed. It takes a few hours to absorb the moisture, and low temperatures also slow down the process.

en: Please check if the SD card is inserted into the printer.
    If it still cannot be read, you can try formatting the SD card.
en: Please check if the Micro SD card is inserted into the printer.
    If it still cannot be read, you can try formatting the card.

en: Please check the network and try again, You can restart or update the printer if the issue persists.
en: Please check the network and try again. You can restart or update the printer if the issue persists.

en: Please confirm explosion ratio = 1,and please select at least one object
en: Please confirm explosion ratio = 1, and please select at least one object

en: Please correct them in the param tabs
en: Please correct them in the Param tabs

en: Please enter the IP of printer to connect.
en: Please enter the IP of the printer to connect.

en: Please find the corner with perfect degree of extrusion
en: Please find the corner with the perfect degree of extrusion

en: Please go to filament setting to edit your presets if you need.
    Please note that nozzle temperature, hot bed temperature, and maximum volumetric speed has a significant impact on printing quality. Please set them carefully.
en: Please go to filament settings to edit your presets if you need to.
    Please note that nozzle temperature, hot bed temperature, and maximum volumetric speed each have a significant impact on printing quality. Please set them carefully.

en: Please right click to assembly these objects.
en: Please right click to assemble these objects.

en: Please select a type you want to export
en: Please select a preset type you want to export

en: Portions copyright
en: License Info

en: Power on update
en: Update on startup

en: Preset "%1%" already exists and is incompatible with current printer.
en: Preset "%1%" already exists and is incompatible with the current printer.

en: Preset path is not found, please reselect vendor.
en: Preset path is not found; please reselect vendor.

en: Preset(Old)
en: Preset (Old)

en: Print By Object: 
    Suggest to use auto-arrange to avoid collisions when printing.
en: Print By Object: 
    We suggest using auto-arrange to avoid collisions when printing.

en: Print file not found, Please slice it again and send it for printing.
en: Print file not found; please slice it again and send it for printing.

en: Printer and all the filament&process presets that belong to the printer. 
    Can be shared with others.
en: Printer and all the filament & process presets that belong to the printer,
    Can be shared with others

en: Problem occured. Please update the printer firmware and try again.
en: A problem occurred. Please update the printer firmware and try again.

en: Pull back current filament
en: Pull back the current filament

en: QIDIStudio configuration file may be corrupted and is not able to be parsed.Please delete the file and try again.
en: QIDIStudio configuration file is not able to be parsed and may be corrupted. Please delete the file and try again.

en: QIDIStudio will terminate because of a localization error. It will be appreciated if you report the specific scenario this issue happened.
en: QIDIStudio will terminate because of a localization error. We would appreciate it if you report the specific scenario in which this issue happened.

en: QIDIStudio will terminate because of running out of memory.It may be a bug. It will be appreciated if you report the issue to our team.
en: QIDIStudio will terminate because of running out of memory. It may be a bug. We would greatly appreciate it if you report the issue to our team.

en: Recommended nozzle temperature of this filament type is [%d, %d] degree centigrade
en: The recommended nozzle temperature for this filament type is [%d, %d] degrees centigrade

en: Recommended nozzle temperature range of this filament. 0 means no set
en: Recommended nozzle temperature range of this filament. 0 means not set

en: Refreshing the historical Flow Dynamics Calibration records
en: Refreshing the previous Flow Dynamics Calibration records

en: Resume Printing(defects acceptable)
en: Resume Printing (defects acceptable)

en: Resume Printing(problem solved)
en: Resume Printing (problem solved)

en: Right button click the icon to drop the object printable property
en: Right click the icon to drop the object printable property

en: Right button click the icon to drop the object settings
en: Right click the icon to drop the object settings

en: SD Card
en: MicroSD Card

en: SD Card Abnormal
en: MicroSD Card Abnormal

en: Same as Global Bed Type
en: Same as Global Plate Type

en: Send to Printer SD card
en: Send to Printer MicroSD card

en: Sending gcode file to sdcard
en: Sending gcode file to Micro SD card

en: Show the list of the keyboard shortcuts
en: Show the list of keyboard shortcuts

en: Slice all plate to obtain time and filament estimation
en: Slice all plates to obtain time and filament estimation

en: Slow down for overhang
en: Slow down for overhangs

en: Speed for reloading filament into extruder. Zero means the same speed as retraction
en: Speed for reloading filament into extruder: 0 means the same speed as retraction

en: Speed of auxiliary part cooling fan. Auxiliary fan will run at this speed during printing except the first several layers which are defined by no cooling layers
en: Speed of auxiliary part cooling fan. The auxiliary fan will run at this speed during printing, except for the first several layers, which are defined by no cooling layers

en: Speed of exhaust fan during printing.This speed will overwrite the speed in filament custom gcode
en: Speed of exhaust fan during printing.This speed will override the speed in filament custom g-code

en: Speed of outer wall which is outermost and visible. It's used to be slower than inner wall speed to get better quality.
en: This is the printing speed for the outer walls of parts. These are generally printed slower than inner walls for higher quality.

en: Split to objects
en: Split to Objects

en: Split to parts
en: Split to Parts

en: Studio will remember build plate selected last time for certain printer model.
en: Studio will remember build plate selected last time for certain printer models.

en: Support control chamber temperature
en: Support controlling chamber temperature

en: Support filament
en: Filament for Supports

en: Support material is commonly used to print support and support interface
en: Support material is commonly used to print support and support interfaces.

en: Support painting
en: Support Painting

en: Switch to rectilinear pattern?
    Yes - switch to rectilinear pattern automatically
    No  - reset density to default non 100% value automatically
en: Switch to rectilinear pattern?
    Yes - switch to rectilinear pattern
    No  - reset density to default non 100% value

en: Synchronizing device information time out
en: Synchronizing device information timed out

en: Thank you for purchasing a QIDI TECH device.Before using your QIDI TECH device, please read the termsand conditions.By clicking to agree to use your QIDI TECH device, you agree to abide by the Privacy Policy and Terms of Use(collectively, the "Terms"). If you do not comply with or agree to the QIDI TECH Privacy Policy, please do not use QIDI TECH equipment and services.
en: Thank you for purchasing a QIDI TECH device. Before using your QIDI TECH device, please read the terms and conditions. By clicking to agree to use your QIDI TECH device, you agree to abide by the Privacy Policy and Terms of Use (collectively, the "Terms"). If you do not comply with or agree to the QIDI TECH Privacy Policy, please do not use QIDI TECH equipment and services.

en: The '%s' folder already exists in the current directory. Do you want to clear it and rebuild it.
    If not, a time suffix will be added, and you can modify the name after creation.
en: The '%s' folder already exists in the current directory. Do you want to clear it and rebuild it?
    If not, a time suffix will be added, and you can modify the name after creation.

en: The .gcode.3mf file contains no G-code data.Please slice it whth QIDI Studio and export a new .gcode.3mf file.
en: The .gcode.3mf file contains no G-code data.Please slice it with QIDIStudio and export a new .gcode.3mf file.

en: The 3mf has following modified G-codes in filament or printer presets:
en: The 3mf has following modified G-code in filament or printer presets:

en: The AMS will automatically read the filament information when inserting a new QIDI TECH filament. This takes about 20 seconds.
en: The AMS will automatically read the filament information when inserting a new QIDI TECH filament spool. This takes about 20 seconds.

en: The AMS will automatically read the information of inserted filament on start-up. It will take about 1 minute.The reading process will roll filament spools.
en: The AMS will automatically read the information of inserted filament on start-up. It will take about 1 minute.The reading process will rotate the filament spools.

en: The Filament name %s you created already exists. 
    If you continue creating, the preset created will be displayed with its full name. Do you want to continue?
en: The Filament name %s you created already exists. 
    If you continue, the preset created will be displayed with its full name. Do you want to continue?

en: The QIDI Studio needs an upgrade
en: QIDI Studio needs an update

en: The QIDI Studio version is too old to enable cloud service. Please download the latest version from QIDI TECH website.
en: The QIDI Studio version is too old to enable cloud service. Please download the latest version from QIDI TECH's website.

en: The Wipe option is not available when using the Firmware Retraction mode.
    
    Shall I disable it in order to enable Firmware Retraction?
en: The Wipe option is not available when using the Firmware Retraction mode.
    
    Disable it in order to enable Firmware Retraction?

en: The current chamber temperature or the target chamber temperature exceeds 45℃.In order to avoid extruder clogging,low temperature filament(PLA/PETG/TPU) is not allowed to be loaded.
en: The current chamber temperature or the target chamber temperature exceeds 45℃. In order to avoid extruder clogging, low temperature filament (PLA/PETG/TPU) is not allowed to be loaded.

en: The current hot bed temperature is relatively high. The nozzle may be clogged when printing this filament in a closed enclosure. Please open the front door and/or remove the upper glass.
en: The current heatbed temperature is relatively high. The nozzle may clog when printing this filament in a closed environment. Please open the front door and/or remove the upper glass.

en: The current project has unsaved changes, save it before continue?
en: The current project has unsaved changes; would you like to save before continuing?

en: The current project has unsaved changes, save it before continuing?
en: The current project has unsaved changes; would you like to save before continuing?

en: The custom printer or model is not inputed, place input.
en: The custom printer or model missing; please input.

en: The file %s already exists
    Do you want to replace it?
en: The file %s already exists.
    Do you want to replace it?

en: The largest printable layer height for extruder. Used to limit the maximum layer height when enable adaptive layer height
en: The largest printable layer height for extruder. Used to limit the maximum layer height when using adaptive layer height

en: The lowest printable layer height for extruder. Used to limit the minimum layer height when enable adaptive layer height
en: The lowest printable layer height for extruder. Used to limit the minimum layer height when using adaptive layer height

en: The material softens at this temperature, so when the bed temperature is equal to or greater than it, it's highly recommended to open the front door and/or remove the upper glass to avoid cloggings.
en: The material softens at this temperature, so when the bed temperature is equal to or greater than this, it's highly recommended to open the front door and/or remove the upper glass to avoid clogs.

en: The metallic material of nozzle. This determines the abrasive resistance of nozzle, and what kind of filament can be printed
en: The metallic material of the nozzle: This determines the abrasive resistance of the nozzle and what kind of filament can be printed.

en: The model is not fond, place reselect vendor.
en: The model was not found; please reselect vendor.

en: The name is not allowed to end with space character.
en: The name is not allowed to end with a space.

en: The name is not allowed to start with space character.
en: The name is not allowed to start with a space.

en: The nozzle diameter is not fond, place reselect.
en: The nozzle diameter was not found; please reselect.

en: The number of bottom solid layers is increased when slicing if the thickness calculated by bottom shells layers is thinner than this value. This can avoid having too thin shell when layer height is small. 0 means that this setting is disabled and thickness of bottom shell is absolutely determained by bottom shell layers
en: The number of bottom solid layers is increased when slicing if the thickness calculated by bottom shells layers is thinner than this value. This can avoid having an overly thin shell when layer height is small. 0 means that this setting is disabled and thickness of bottom shell is determined by bottom shell layers.

en: The number of top solid layers is increased when slicing if the thickness calculated by top shell layers is thinner than this value. This can avoid having too thin shell when layer height is small. 0 means that this setting is disabled and thickness of top shell is absolutely determained by top shell layers
en: The number of top solid layers is increased when slicing if the thickness calculated by top shell layers is thinner than this value. This can avoid having too thin a shell when layer height is small. 0 means that this setting is disabled and thickness of top shell is determined simply by the number of top shell layers.

en: The object from file %s is too small, and maybe in meters or inches.
     Do you want to scale to millimeters?
en: The object from file %s is too small, and may be in meters or inches.
     Do you want to scale to millimeters?

en: The player is not loaded, please click "play" button to retry.
en: The player is not loaded; please click the "play" button to retry.

en: The prime tower requires that support has the same layer height as object.
en: The prime tower requires that supports have the same layer height as objects.

en: The printer does not support sending to printer SD card.
en: The printer does not support sending to printer Micro SD card.

en: The printer is busy on other print job
en: The printer is busy with another print job.

en: The printer preset is not fond, place reselect.
en: The printer preset was not found; please reselect.

en: The printer preset you created already has a preset with the same name. Do you want to overwrite it?
    	Yes: Overwrite the printer preset with the same name, and filament and process presets with the same preset name will be recreated 
    and filament and process presets without the same preset name will be reserve.
    	Cancel: Do not create a preset, return to the creation interface.
en: The printer preset you created already has a preset with the same name. Do you want to overwrite it?
    	Yes: Overwrite the printer preset with the same name, and filament and process presets with the same preset name will be recreated 
    and filament and process presets without the same preset name will be reserved.
    	Cancel: Do not create a preset; return to the creation interface.

en: The target object contains only one part and can not be split.
en: The target object contains only one part and cannot be split.

en: The vendor can not be a number. Please re-enter.
en: The vendor can not be a number; please re-enter.

en: There is already a historical calibration result with the same name: %s. Only one of the results with the same name is saved. Are you sure you want to override the historical result?
en: There is already a previous calibration result with the same name: %s. Only one result with a name is saved. Are you sure you want to overwrite the previous result?

en: There may be escape characters in the vendor or serial input of filament. Please delete and re-enter.
en: There may be disallowed characters in the vendor or serial input of the filament. Please delete and re-enter.

en: This action will break a cut correspondence.
    After that model consistency can't be guaranteed .
    
    To manipulate solid parts or negative volumes you have to invalidate cut information first.
en: This action will break a cut correspondence.
    After that, model consistency can't be guaranteed.
    
    To manipulate solid parts or negative volumes you have to invalidate cut information first.

en: This factor affects the acreage of top area. The small the number the big the top area.
en: This factor affects the size of the top area. Smaller numbers mean a bigger top area.

en: This is neither a commonly used filament, nor one of QIDI filaments, and it varies a lot from brand to brand. So, it's highly recommended to ask its vendor for suitable profile before printing and adjust some parameters according to its performances.
en: This is neither a commonly used filament, nor a QIDI filament, and it varies a lot from brand to brand, so it's highly recommended to ask the vendor for a suitable profile before printing and adjust some parameters according to its performance.

en: This is the number of solid layers of top shell, including the top surface layer. When the thickness calculated by this value is thinner than top shell thickness, the top shell layers will be increased
en: This is the number of solid layers of top shell, including the top surface layer. When the thickness calculated by this value is thinner than the top shell thickness, the top shell layers will be increased

en: This machine type can only hold %d history results per nozzle.
en: This machine type can only hold %d historical results per nozzle.

en: This machine type can only hold %d history results per nozzle. This result will not be saved.
en: This machine type can only hold %d historical results per nozzle. This result will not be saved.

en: This machine type can only hold 16 history results per nozzle. You can delete the existing historical results and then start calibration. Or you can continue the calibration, but you cannot create new calibration historical results. 
    Do you still want to continue the calibration?
en: This machine type can only hold 16 historical results per nozzle. You can delete the existing historical results and then start calibration. Or you can continue the calibration, but you cannot create new calibration historical results. 
    Do you still want to continue the calibration?

en: This plate is locked,
    We can not do auto-arrange on this plate.
en: This plate is locked.
    We cannot auto-arrange this plate.

en: This plate is locked,
    We can not do auto-orient on this plate.
en: This plate is locked.
    We cannot auto-orient this plate.

en: This setting is only used for model size tuning with small value in some cases.
    For example, when the model size has slight errors and is difficult be assembled.
    For large size tuning, please use model scaling function.
    
    The value will be reset to 0.
en: This setting is only used for model size tuning with small values in some cases.
    For example, when the model size has slight errors and assembly is difficult.
    For large size tuning, please use the model scaling function.
    
    The value will be reset to 0.

en: Too large elephant foot compensation is unreasonable.
    If really have serious elephant foot effect, please check other settings.
    For example, whether bed temperature is too high.
    
    The value will be reset to 0.
en: Too large an elephant foot compensation is a problem.
    For very serious elephant foot effects, please check other settings.
    For example, bed temperature may be too high.
    
    The value will be reset to 0.

en: Too large line width
en: Line width too large

en: Too small line width
en: Line width too small

en: Undefine
en: Undefined

en: Unknown file format. Input file must have .3mf or .zip.amf extension.
en: Unknown file format: input file must have .3mf or .zip.amf extension.

en: Use only one wall on flat top surface, to give more space to the top infill pattern. Could be applied on topmost surface or all top surface.
en: Use only one wall on flat top surface to give more space to the top infill pattern. Can be applied on topmost surface or all top surfaces

en: Vendor is not found, please reselect.
en: Vendor is not found; please reselect.

en: Vendor is not selected, please reselect vendor.
en: Vendor is not selected; please reselect vendor.

en: Volume of nozzle between the cutter and the end of nozzle
en: Volume of nozzle between the filament cutter and the end of the nozzle

en: Waring:The count of newly added and 
     current extruders exceeds 16.
en: Warning: The count of newly added and 
     current extruders exceeds 16.

en: Warning:please select Plane's feature.
en: Warning: please select Plane's feature.

en: Warning:please select Point's or Circle's feature.
en: Warning: please select Point's or Circle's feature.

en: Warning:please select two different mesh.
en: Warning: please select two different meshes.

en: We would rename the presets as "Vendor Type Serial @printer you selected". 
    To add preset for more prinetrs, Please go to printer selection
en: We would rename the presets as "Vendor Type Serial @printer you selected". 
    To add preset for more printers; please go to printer selection

en: When enable spiral vase mode, machines with I3 structure will not generate timelapse videos.
en: When spiral vase mode is enabled, machines with I3 structure will not generate timelapse videos.

en: When need to print with the printer door opened
    Did you know that opening the printer door can reduce the probability of extruder/hotend clogging when printing lower temperature filament with a higher enclosure temperature. More info about this in the Wiki.
en: When do you need to print with the printer door opened?
    Did you know that opening the printer door can reduce the probability of extruder/hotend clogging when printing lower temperature filament with a higher enclosure temperature? There is more info about this in the Wiki.

en: When sparse infill density is low, the internal solid infill or internal bridge may have no archor at the end of line. This causes falling and bad quality when printing internal solid infill. When enable this feature, loop paths will be added to the sparse fill of the lower layers for specific thickness, so that better archor can be provided for internal bridge. 0 means disable this feature
en: When sparse infill density is low, the internal solid infill or internal bridge may have no anchor at the end of lines. This causes falling and decreased quality when printing internal solid infill. When this feature is enabled, loop paths will be added to the sparse fill of the lower layers to attain a specific thickness, so that better anchoring can be provided for internal bridges. 0 disables this feature.

en: When you set the chamber temperature below 40℃, the chamber temperature control will not be activated. And the target chamber temperature will automatically be set to 0℃.
en: When you set the chamber temperature below 40℃, the chamber temperature control will not be activated, and the target chamber temperature will automatically be set to 0℃.

en: Whenever the retraction is done, the nozzle is lifted a little to create clearance between nozzle and the print. It prevents nozzle from hitting the print when travel moves. Using spiral line to lift z can prevent stringing
en: Whenever there is a retraction, the nozzle is lifted a little to create clearance between the nozzle and the print. This prevents the nozzle from hitting the print when traveling. Using a spiral line to lift z can prevent stringing.

en: Whether the machine supports silent mode in which machine use lower acceleration to print
en: Whether the machine supports silent mode in which machine uses lower acceleration to print more quietly

en: Would you like to log in this printer with current account?
en: Would you like to log in this printer with the current account?

en: You can find it in "Settings > Network > Connection code"
    on the printer, as shown in the figure:
en: You can find it in "Settings > Network > Access code"
    on the printer, as shown in the figure:

en: You have completed printing the mall model, 
    but the synchronization of rating information has failed.
en: You have completed printing the mall model, 
    but synchronizing rating information has failed.

en: You have entered an illegal input in the printable area section on the first page. Please check before creating it.
en: You have entered a disallowed character in the printable area section on the first page. Please use only numbers.

en: You have not selected the vendor and model or inputed the custom vendor and model.
en: You have not selected the vendor and model or input the custom vendor and model.

en: You have not yet selected the printer to replace the nozzle, please choose.
en: You have not yet selected the printer to replace the nozzle for; please choose a printer.

en: Your comment result cannot be uploaded due to some reasons. As follows:
    
      error code:
en: Your comment result cannot be uploaded due to the following reasons:
    
      error code:

en: Your model needs support ! Please make support material enable.
en: Your model needs support! Please enable support material.

en: Your nozzle diameter in preset is not consistent with memorized nozzle diameter. Did you change your nozzle lately?
en: Your nozzle diameter in preset is not consistent with the saved nozzle diameter. Have you changed your nozzle?

en: Your nozzle diameter in sliced file is not consistent with memorized nozzle. If you changed your nozzle lately, please go to Device > Printer Parts to change settings.
en: Your nozzle diameter in sliced file is not consistent with the saved nozzle. If you changed your nozzle lately, please go to Device > Printer Parts to change settings.

en: archive too large
en: Archive too large

en: buffer too small
en: Buffer too small

en: connectors is out of object
en: Connectors must be on object surface.

en: file too large
en: File too large

en: keyboard 1-9: set filament for object/part
en: Keyboard 1-9: set filament for object/part

en: minute each batch.(It depends on how long it takes to complete the heating.)
en: minute each batch. (It depends on how long it takes to complete heating.)

en: non-manifold edges be caused by cut tool, do you want to fix it now?
en: Non-manifold edges be caused by cut tool: do you want to fix now?

en: printers at the same time.(It depends on how many devices can undergo heating at the same time.)
en: printers at the same time. (It depends on how many devices can undergo heating at the same time.)

en: the configuration package is incompatible with current application.
en: the configuration package is incompatible with the current application.
