QIDI Studio - en to en translation catalogue (517 entries)

en: 
    
    Would you like to redirect to the webpage for rating?
en: 
    
    Would you like to redirect to the webpage to give a rating?

en:  can not be opened
en:  cannot be opened

en:  is too close to clumping detection area, and collisions will be caused.
en:  is too close to probing area of clumping detection, and collisions will be caused.

en:  is too close to clumping detection area, there may be collisions when printing.
en:  is too close to probing area of clumping detection, there may be collisions when printing.

en:  is too close to exclusion area, and collisions will be caused.
en:  is too close to an exclusion area, and collisions will be caused.

en: %1% is too close to exclusion area, there may be collisions when printing.
en: %1% is too close to exclusion area. There may be collisions when printing.

en: %s can't be percentage
en: %s can't be a percentage

en: - Part mode: Please select one object with at least two meshes.
en: - Part mode: Please select one object with at least two parts.

en: A G-code path goes beyond the boundary of plate.
en: A G-code path goes beyond plate boundaries.

en: A config exists with the same name: %s, do you want to override it.
en: A config exists with the same name: %s; do you want to replace it?

en: A file exists with the same name: %s, do you want to override it.
en: A file exists with the same name: %s; do you want to replace it?

en: A gap between innermost brim line and object can make brim be removed more easily
en: This creates a gap between the innermost brim line and the object and can make the brim easier to remove.

en: A test model will be printed. Please clear the build plate and place it back to the hot bed before calibration.
en: A test model will be printed. Please clear the build plate and place it back on the heatbed before calibration.

en: AMS filaments
en: AMS filament

en: AMS will continue to another spool with the same properties of filament automatically when current filament runs out
en: AMS will continue to another spool with the same filament properties automatically when current filament runs out.

en: Acceleration of initial layer. Using a lower value can improve build plate adhensive
en: Acceleration of initial layer. Using a lower value can improve build plate adhesion.

en: Acceleration of top surface infill. Using a lower value may improve top surface quality
en: This is the acceleration of top surface infill. Using a lower value may improve top surface quality.

en: Add plate
en: Add Plate

en: Add solid infill near sloping surfaces to guarantee the vertical shell thickness (top+bottom solid layers)
en: Add solid infill near sloping surfaces to guarantee the vertical shell thickness (top+bottom solid layers).

en: Advance
en: Advanced

en: All the selected objects are on the locked plate,
    We can not do auto-arrange on these objects.
en: All the selected objects are on a locked plate.
    Cannot auto-arrange these objects.

en: All the selected objects are on the locked plate,
    We can not do auto-orient on these objects.
en: All the selected objects are on a locked plate,
    We cannot auto-orient these objects.

en: Ams Status
en: AMS Status

en: An error occurred. Maybe memory of system is not enough or it's a bug of the program
en: An error occurred. System memory may not be enough or it may be a program bug.

en: An important update was detected and needs to be run before printing can continue. Do you want to update now? You can also update later from 'Upgrade firmware'.
en: An important update was detected and needs to be run before printing can continue. Do you want to update now? You can also update later from 'Update firmware'.

en: An object is laid over the boundary of plate or exceeds the height limit.
    Please solve the problem by moving it totally on or off the plate, and confirming that the height is within the build volume.
en: An object is laid over the boundary of the plate or exceeds the height limit.
    Please solve the problem by moving it totally on or off the plate, and confirming that the height is within the build volume.

en: An object is layed over the boundary of plate.
en: An object is laid over the boundary of the plate.

en: Angle for sparse infill pattern, which controls the start or main direction of line
en: This is the angle for sparse infill pattern, which controls the start or main direction of lines.

en: Are you sure to %1% the selected preset?
en: Are you sure you want to %1% the selected preset?

en: Are you sure to cancel the current calibration and return to the home page?
en: Are you sure you want to cancel the current calibration and return to the home page?

en: Arranging is done but there are unpacked items. Reduce spacing and try again.
en: Arranging complete, but some items were not able to be arranged. Reduce spacing and try again.

en: Assemble the selected objects to an object with multiple parts
en: Assemble the selected objects into an object with multiple parts

en: Assemble the selected objects to an object with single part
en: Assemble the selected objects into an object that is a single part

en: At least one successful print record of this print profile is required 
    to give a positive rating(4 or 5stars).
en: At least one successful print record of this print profile is required 
    to give a positive rating (4 or 5 stars).

en: Auto Flow Rate Calibration utilizes QIDI Tech's Micro-Lidar technology, directly measuring the calibration patterns. However, please be advised that the efficacy and accuracy of this method may be compromised with specific types of materials. Particularly, filaments that are transparent or semi-transparent, sparkling-particled, or have a high-reflective finish may not be suitable for this calibration and can produce less-than-desirable results.
    
    The calibration results may vary between each calibration or filament. We are still improving the accuracy and compatibility of this calibration through firmware updates over time.
    
    Caution: Flow Rate Calibration is an advanced process, to be attempted only by those who fully understand its purpose and implications. Incorrect usage can lead to sub-par prints or printer damage. Please make sure to carefully read and understand the process before doing it.
en: Auto Flow Rate Calibration utilizes QIDI Tech's Micro-Lidar technology, directly measuring the calibration patterns. However, please be advised that the efficacy and accuracy of this method may be compromised with specific types of materials. Particularly, filaments that are transparent or semi-transparent, have sparkles, or have a highly-reflective finish may not be suitable for this calibration and can produce less-than-desirable results.
    
    The calibration results may vary between each calibration or filament. We are still improving the accuracy and compatibility of this calibration through firmware updates over time.
    
    Caution: Flow Rate Calibration is an advanced process, to be attempted only by those who fully understand its purpose and implications. Incorrect usage can lead to sub-par prints or printer damage. Please make sure to carefully read and understand the process before doing it.

en: Auto orient
en: Auto Orient

en: Auto orientates selected objects or all objects.If there are selected objects, it just orientates the selected ones.Otherwise, it will orientates all objects in the current disk.
en: This auto orients selected objects or all objects. If there are selected objects, it just orients the selected ones. Otherwise, it will orient all objects in the current plate.

en: Auto sync user presets(Printer/Filament/Process)
en: Auto sync user presets (Printer/Filament/Process)

en: Auto-Arrange
    Did you know that you can auto-arrange all objects in your project?
en: Auto-Arrange
    Did you know that you can auto-arrange all the objects in your project?

en: Auto-Orient
    Did you know that you can rotate objects to an optimal orientation for printing by a simple click?
en: Auto-Orient
    Did you know that you can rotate objects to an optimal orientation for printing with a simple click?

en: Auto-recovery from step loss
en: Auto-recover from step loss

en: Automatically Combine sparse infill of several layers to print together to reduce time. Wall is still printed with original layer height.
en: Automatically combine sparse infill of several layers to print together in order to reduce time. Walls are still printed with original layer height.

en: Avoid warping
    Did you know that when printing materials that are prone to warping such as ABS, appropriately increasing the heatbed temperature can reduce the probability of warping.
en: Avoid warping
    Did you know that when printing materials that are prone to warping such as ABS, appropriately increasing the heatbed temperature can reduce the probability of warping?

en: Backup your project periodically for restoring from the occasional crash.
en: Backup your project periodically to help with restoring from an occasional crash.

en: Bed Type
en: Plate Type

en: Bed adhension
en: Bed adhesion

en: Bed temperature for layers except the initial one. Value 0 means the filament does not support to print on the Cool Plate
en: This is the bed temperature for layers except for the first one. A value of 0 means the filament does not support printing on the Cool Plate.

en: Bed temperature for layers except the initial one. Value 0 means the filament does not support to print on the Engineering Plate
en: This is the bed temperature for layers except for the first one. A value of 0 means the filament does not support printing on the Engineering Plate.

en: Bed temperature for layers except the initial one. Value 0 means the filament does not support to print on the High Temp Plate
en: This is the bed temperature for layers except for the first one. A value of 0 means the filament does not support printing on the High Temp Plate.

en: Bed temperature for layers except the initial one. Value 0 means the filament does not support to print on the Textured PEI Plate
en: Bed temperature after the first layer. 0 means the filament is not supported on the Textured PEI Plate.

en: Bed temperature of the initial layer. Value 0 means the filament does not support to print on the Cool Plate
en: This is the bed temperature of the first layer. A value of 0 means the filament does not support printing on the Cool Plate.

en: Bed temperature of the initial layer. Value 0 means the filament does not support to print on the Engineering Plate
en: This is the bed temperature of the first layer. A value of 0 means the filament does not support printing on the Engineering Plate.

en: Bed temperature of the initial layer. Value 0 means the filament does not support to print on the High Temp Plate
en: This is the bed temperature of the first layer. A value of 0 means the filament does not support printing on the High Temp Plate.

en: Bed temperature of the initial layer. Value 0 means the filament does not support to print on the Textured PEI Plate
en: Bed temperature of the first layer 0 means the filament is not supported on the Textured PEI Plate.

en: Bed temperature when Textured PEI Plate is installed. Value 0 means the filament does not support to print on the Textured PEI Plate
en: Bed temperature when Textured PEI Plate is installed. 0 means the filament is not supported on the Textured PEI Plate

en: Bed temperature when cool plate is installed. Value 0 means the filament does not support to print on the Cool Plate
en: This is the bed temperature when the cool plate is installed. A value of 0 means the filament does not support printing on the Cool Plate.

en: Bed temperature when engineering plate is installed. Value 0 means the filament does not support to print on the Engineering Plate
en: This is the bed temperature when the engineering plate is installed. A value of 0 means the filament does not support printing on the Engineering Plate.

en: Bed type
en: Plate type

en: Bed types supported by the printer
en: Plate types supported by the printer

en: Bridging angle override. If left to zero, the bridging angle will be calculated automatically. Otherwise the provided angle will be used for external bridges. Use 180°for zero angle.
en: Bridging angle override. 0 means the bridging angle will be calculated automatically. Otherwise the provided angle will be used for external bridges. Use 180° for zero angle.

en: Brim for better adhesion
    Did you know that when printing models have a small contact interface with the printing surface, it's recommended to use a brim?
en: Brim for better adhesion
    Did you know that when printed models have a small contact interface with the printing surface, it's recommended to use a brim?

en: CF/GF filaments are hard and brittle, It's easy to break or get stuck in AMS, please use with caution.
en: CF/GF filaments are hard and brittle, so they can easily break or get stuck in an AMS; please use with caution.

en: Can not add models when in preview mode!
en: Unable to add models in preview mode

en: Can not print multiple filaments which have large difference of temperature together. Otherwise, the extruder and nozzle may be blocked or damaged during printing
en: Unable to print multiple filaments which have large temperature differences together. Otherwise, the extruder and nozzle may be blocked or damaged during printing.

en: Can't apply when process preview.
en: Can't apply when processing preview

en: Cancle
en: Cancel

en: Cannot read filament info: the filament is loaded to the tool head,please unload the filament and try again.
en: Cannot read filament info: the filament is loaded to the tool head. Please unload the filament and try again.

en: Cannot send the print job to a printer whose firmware is required to get updated.
en: Cannot send the print job to a printer whose firmware must be updated.

en: Cannot send the print task when the upgrade is in progress
en: Cannot send print tasks when an update is in progress

en: Change these settings automatically? 
    Yes - Change these settings and enable spiral mode automatically
    No  - Give up using spiral mode this time
en: Change these settings automatically? 
    Yes - Change these settings and enable spiral/vase mode automatically
    No  - Cancel enabling spiral mode

en: Change these settings automatically? 
    Yes - Change these settings automatically
    No  - Do not change these settings for me
en: Change these settings automatically? 
    Yes - Change these settings automatically.
    No  - Do not change these settings for me.

en: Changing the region will log out your account.
en: Changing the region will log you out of your account.

en: Check for Update
en: Check for Updates

en: Check if the nozzle is clumping by filaments or other foreign objects.
en: Check if the nozzle is clumped with filament or other foreign objects.

en: Check the current status of the qidi server by clicking on the link above.
en: Check the current status of the QIDI Tech server by clicking on the link above.

en: Choose an AMS slot then press "Load" or "Unload" button to automatically load or unload filaments.
en: Choose an AMS slot then press "Load" or "Unload" button to automatically load or unload filament.

en: Classic wall generator produces walls with constant extrusion width and for very thin areas is used gap-fill. Arachne engine produces walls with variable extrusion width
en: The classic wall generator produces walls with constant extrusion width and for very thin areas, gap-fill is used. The Arachne engine produces walls with variable extrusion width.

en: Click OK to update the Network plug-in when QIDI Studio launches next time.
en: Click OK to update the Network plug-in the next time QIDI Studio launches.

en: Click the icon to edit color painting of the object
en: Click the icon to edit color painting for the object

en: Click the icon to toggle printable property of the object
en: Click the icon to toggle printable properties of the object

en: Click to drop current modify and reset to saved value.
en: Click to drop current modifications and reset to saved value.

en: Click to pick filament color
en: Click to select filament color

en: Clumping Detection G-code
en: G-code of clumping detection by probing

en: Clumping detection G-code
en: G-code of clumping detection by probing

en: Clumping detection is not supported when "by object" sequence is enabled.
en: Clumping detection by probing is not supported when "by object" sequence is enabled.

en: Clumping detection layers
en: Layers of clumping detection by probing

en: Clumping detection layers.
en: Layers of clumping detection by probing.

en: Color painting
en: Color Painting

en: Colour
en: Color

en: Comfirm Save As
en: Confirm Save As

en: Compared with the default profile of 0.2 mm nozzle, it has a smaller layer height, and results in minimal layer lines and higher printing quality, but shorter printing time.
en: Compared with the default profile of 0.2 mm nozzle, it has a smaller layer height. This results in minimal layer lines and higher print quality but longer print time.

en: Compared with the default profile of a 0.2 mm nozzle, it has a bigger layer height, and results in slightly visible layer lines, but shorter printing time.
en: Compared with the default profile of a 0.2 mm nozzle, it has a bigger layer height. This results in slightly visible layer lines but shorter print time.

en: Compared with the default profile of a 0.2 mm nozzle, it has a slightly bigger layer height, and results in almost negligible layer lines, and slightly shorter printing time.
en: Compared with the default profile of a 0.2 mm nozzle, it has a slightly bigger layer height. This results in almost negligible layer lines and slightly longer print time.

en: Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer height, and results in almost invisible layer lines and higher printing quality, but shorter printing time.
en: Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer height. This results in almost invisible layer lines and higher print quality but longer print time.

en: Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer lines, lower speeds and acceleration, and the sparse infill pattern is Gyroid. So, it results in almost invisible layer lines and much higher printing quality, but much longer printing time.
en: Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer lines, lower speeds and acceleration, and the sparse infill pattern is Gyroid. This results in almost invisible layer lines and much higher print quality but much longer print time.

en: Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer lines, lower speeds and acceleration, and the sparse infill pattern is Gyroid. So, it results in minimal layer lines and much higher printing quality, but much longer printing time.
en: Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer lines, lower speeds and acceleration, and the sparse infill pattern is Gyroid. This results in minimal layer lines and much higher print quality but much longer print time.

en: Compared with the default profile of a 0.2 mm nozzle, it has lower speeds and acceleration, and the sparse infill pattern is Gyroid. So, it results in much higher printing quality, but a much longer printing time.
en: Compared with the default profile of a 0.2 mm nozzle, it has lower speeds and acceleration, and the sparse infill pattern is Gyroid. This results in much higher print quality but a much longer print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a bigger layer height, and results in more apparent layer lines and lower printing quality, but shorter printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a bigger layer height. This results in more apparent layer lines and lower print quality but shorter print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a bigger layer height, and results in more apparent layer lines and lower printing quality, but slightly shorter printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a bigger layer height. This results in more apparent layer lines and lower print quality but slightly shorter print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, and results in almost negligible layer lines and higher printing quality, but longer printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height. This results in almost negligible layer lines and higher print quality but longer print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, and results in almost negligible layer lines and longer printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height. This results in almost negligible layer lines and longer print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, and results in less apparent layer lines and higher printing quality, but longer printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height. This results in less apparent layer lines and higher print quality but longer print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, lower speeds and acceleration, and the sparse infill pattern is Gyroid. So, it results in almost negligible layer lines and much higher printing quality, but much longer printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, lower speeds and acceleration, and the sparse infill pattern is Gyroid. This results in almost negligible layer lines and much higher print quality but much longer print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, lower speeds and acceleration, and the sparse infill pattern is Gyroid. So, it results in less apparent layer lines and much higher printing quality, but much longer printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer height, lower speeds and acceleration, and the sparse infill pattern is Gyroid. This results in less apparent layer lines and much higher print quality but much longer print time.

en: Compared with the default profile of a 0.4 mm nozzle, it has more wall loops and a higher sparse infill density. So, it results in higher strength of the prints, but more filament consumption and longer printing time.
en: Compared with the default profile of a 0.4 mm nozzle, it has more wall loops and a higher sparse infill density. This results in higher print strength but more filament consumption and longer print time.

en: Compared with the default profile of a 0.6 mm nozzle, it has a bigger layer height, and results in more apparent layer lines and lower printing quality, but shorter printing time in some printing cases.
en: Compared with the default profile of a 0.6 mm nozzle, it has a bigger layer height. This results in more apparent layer lines and lower print quality but shorter print time in some cases.

en: Compared with the default profile of a 0.6 mm nozzle, it has a bigger layer height, and results in much more apparent layer lines and much lower printing quality, but shorter printing time in some printing cases.
en: Compared with the default profile of a 0.6 mm nozzle, it has a bigger layer height. This results in much more apparent layer lines and much lower print quality, but shorter print time in some cases.

en: Compared with the default profile of a 0.6 mm nozzle, it has a smaller layer height, and results in less apparent layer lines and higher printing quality, but longer printing time.
en: Compared with the default profile of a 0.6 mm nozzle, it has a smaller layer height. This results in less apparent layer lines and higher print quality but longer print time.

en: Compared with the default profile of a 0.6 mm nozzle, it has a smaller layer height, and results in less apparent layer lines and slight higher printing quality, but longer printing time.
en: Compared with the default profile of a 0.6 mm nozzle, it has a smaller layer height. This results in less apparent layer lines and slightly higher print quality but longer print time.

en: Compared with the default profile of a 0.6 mm nozzle, it has more wall loops and a higher sparse infill density. So, it results in higher strength of the prints, but more filament consumption and longer printing time.
en: Compared with the default profile of a 0.6 mm nozzle, it has more wall loops and a higher sparse infill density. This results in higher print strength but more filament consumption and longer print time.

en: Compared with the default profile of a 0.8 mm nozzle, it has a bigger layer height, and results in very apparent layer lines and much lower printing quality, but shorter printing time in some printing cases.
en: Compared with the default profile of a 0.8 mm nozzle, it has a bigger layer height. This results in very apparent layer lines and much lower print quality but shorter print time in some cases.

en: Compared with the default profile of a 0.8 mm nozzle, it has a much bigger layer height, and results in extremely apparent layer lines and much lower printing quality, but much shorter printing time in some printing cases.
en: Compared with the default profile of a 0.8 mm nozzle, it has a much bigger layer height. This results in extremely apparent layer lines and much lower print quality but much shorter print time in some cases.

en: Compared with the default profile of a 0.8 mm nozzle, it has a slightly smaller layer height, and results in slightly less but still apparent layer lines and slightly higher printing quality, but longer printing time in some printing cases.
en: Compared with the default profile of a 0.8 mm nozzle, it has a slightly smaller layer height. This results in slightly less but still apparent layer lines and slightly higher print quality, but longer print time in some cases.

en: Compared with the default profile of a 0.8 mm nozzle, it has a smaller layer height, and results in less but still apparent layer lines and slightly higher printing quality, but longer printing time in some printing cases.
en: Compared with the default profile of a 0.8 mm nozzle, it has a smaller layer height. This results in less but still apparent layer lines and slightly higher print quality, but longer print time in some cases.

en: Config which AMS slot should be used for a filament used in the print job
en: Configure which AMS slot should be used for a filament used in the print job.

en: Configuration file "%1%" was loaded, but some values were not recognized.
en: The configuration file “%1%” was loaded, but some values were not recognized.

en: Configuration package was loaded, but some values were not recognized.
en: The configuration package was loaded, but some values were not recognized.

en: Conflicts of gcode paths have been found at layer %d. Please separate the conflicted objects farther (%s <-> %s).
en: Conflicts of gcode paths have been found at layer %d. Please separate the conflicting objects further (%s <-> %s).

en: Connect a sparse infill line to an internal perimeter with a short segment of an additional perimeter. If expressed as percentage (example: 15%) it is calculated over sparse infill line width. Slicer tries to connect two close infill lines to a short perimeter segment. If no such perimeter segment shorter than infill_anchor_max is found, the infill line is connected to a perimeter segment at just one side and the length of the perimeter segment taken is limited to this parameter, but no longer than anchor_length_max. Set this parameter to zero to disable anchoring perimeters connected to a single infill line.
en: This connects a sparse infill line to an internal perimeter with a short segment of an additional perimeter. If expressed as percentage (example: 15%) it is calculated over sparse infill line width. QIDI Studio tries to connect two close infill lines to a short perimeter segment. If no such perimeter segment shorter than infill_anchor_max is found, the infill line is connected to a perimeter segment at just one side and the length of the perimeter segment taken is limited to this parameter, but no longer than anchor_length_max. Set this parameter to zero to disable anchoring perimeters connected to a single infill line.

en: Connect a sparse infill line to an internal perimeter with a short segment of an additional perimeter. If expressed as percentage (example: 15%) it is calculated over sparse infill line width. Slicer tries to connect two close infill lines to a short perimeter segment. If no such perimeter segment shorter than this parameter is found, the infill line is connected to a perimeter segment at just one side and the length of the perimeter segment taken is limited to infill_anchor, but no longer than this parameter. Set this parameter to zero to disable anchoring.
en: This connects a sparse infill line to an internal perimeter with a short segment of an additional perimeter. If expressed as percentage (example: 15%) it is calculated over sparse infill line width. QIDI Studio tries to connect two close infill lines to a short perimeter segment. If no such perimeter segment shorter than this parameter is found, the infill line is connected to a perimeter segment at just one side and the length of the perimeter segment taken is limited to infill_anchor, but no longer than this parameter. Set this parameter to zero to disable anchoring.

en: ConnectPrinter(LAN)
en: Connect Printer (LAN)

en: Connection to AstroBox works correctly.
en: Connection to AstroBox is working correctly.

en: Connection to Duet works correctly.
en: Connection to Duet is working correctly.

en: Connection to FlashAir works correctly and upload is enabled.
en: Connection to FlashAir is working correctly and upload is enabled.

en: Connection to MKS works correctly.
en: Connection to MKS is working correctly.

en: Connection to OctoPrint works correctly.
en: Connection to OctoPrint is working correctly.

en: Connection to Prusa SL1 / SL1S works correctly.
en: Connection to Prusa SL1 / SL1S is working correctly.

en: Connection to PrusaLink works correctly.
en: Connection to PrusaLink is working correctly.

en: Connection to Repetier works correctly.
en: Connection to Repetier is working correctly.

en: Contour of object will be grown or shrunk in XY plane by the configured value. Positive value makes contour bigger. Negative value makes contour smaller. This function is used to adjust size slightly when the object has assembling issue
en: The contour of objects will be grown or shrunk in the XY plane by the set value. Positive values make contours bigger, and negative values make contours smaller. This function is used to adjust sizes slightly when objects have assembly issues.

en: Copy paramters
en: Copy parameters

en: Cover the top contact layer of the supports with loops. Disabled by default.
en: This covers the top contact layer of the supports with loops. It is disabled by default.

en: Create Filament Successful
en: Filament Created Successfully

en: Current chamber temperature is higher than the material's safe temperature,it may result in material softening and clogging.The maximum safe temperature for the material is %d
en: Current chamber temperature is higher than the material's safe temperature; this may result in material softening and nozzle clogs.The maximum safe temperature for the material is %d

en: Custom vendor is not input, please input custom vendor.
en: Custom vendor missing; please input custom vendor.

en: Damp PVA is flexible and may get stuck in extruder. Dry it before use.
en: Damp PVA is flexible and may get stuck in the extruder. Please dry it before use.

en: Damp PVA will become flexible and get stuck inside AMS,please take care to dry it before use.
en: Damp PVA will become flexible and get stuck inside the AMS; please take care to dry it well before use.

en: Decide which overhang part join the cooling function to slow down the speed.Expressed as percentage which indicides how much width of the line without support from lower layer. 100% means forcing cooling for all outer wall no matter how much overhang degree
en: Sets the overhang percentage (unsupported width ratio) required to activate print speed-reducing cooling. At 100%% cooling engages for all outer walls regardless of overhang angle

en: Decrease this value slightly(for example 0.9) to reduce the amount of material for bridge, to improve sag
en: Decrease this value slightly (for example 0.9) to reduce the amount of material extruded for bridges to avoid sagging.

en: Density of internal sparse infill, 100% means solid throughout
en: This is the density of internal sparse infill. 100% means that the object will be solid throughout.

en: Detect overhang wall
en: Detect overhang walls

en: Detect the overhang percentage relative to line width and use different speed to print. For 100 percent overhang, bridge speed is used.
en: This detects the overhang percentage relative to line width and use different speed to print. For 100 percent overhang, bridge speed is used.

en: Detect thin wall which can't contain two line width. And use single line to print. Maybe printed not very well, because it's not closed loop
en: This detects thin walls which can’t contain two lines and uses a single line to print. It may not print as well because it’s not a closed loop.

en: Detected that text did not adhere to mesh surface. Please manually drag yellow square to mesh surface that needs to be adhered.
en: Detected that text did not adhere to the mesh surface. Please manually drag the yellow square to mesh surface that the text needs to be adhered to.

en: Detour and avoid traveling across wall which may cause blob on surface
en: Detour and avoid traveling across walls to avoid the possibility of creating blobs on surfaces

en: Difference
en: Subtraction

en: Difference operation requires at least one object in both A and B lists.
en: Subtraction operation requires at least one object in both A and B lists.

en: Difference operation requires at least one volume in both A and B lists.
en: Subtraction operation requires at least one part in both A and B lists.

en: Different types of supports
    Did you know that you can choose from multiple types of supports? Tree supports work great for organic models, while saving filament and improving print speed. Check them out!
en: Different types of supports
    Did you know that you can choose from multiple types of supports? Tree supports work great for organic models while saving filament and improving print speed. Check them out!

en: Distance of the nozzle tip to the lid. Used for collision avoidance in by-object printing.
en: Distance from the nozzle tip to the lid. Used for collision avoidance in by-object printing.

en: Distance of the nozzle tip to the lower rod. Used for collision avoidance in by-object printing.
en: Distance from the nozzle tip to the lower rod. Used for collision avoidance in by-object printing.

en: Do you want to replace it
en: Do you want to replace it?

en: Do you want to synchronize your personal data from QIDI Cloud? 
    It contains the following information:
    1. The Process presets
    2. The Filament presets
    3. The Printer presets
en: Do you want to synchronize your personal data from QIDI Cloud? 
    It contains the following information:
    1. Process presets
    2. Filament presets
    3. Printer presets

en: Don't retract when the travel is in infill area absolutely. That means the oozing can't been seen. This can reduce times of retraction for complex model and save printing time, but make slicing and G-code generating slower
en: Don't retract when the travel is entirely in an infill area. That means the oozing can't been seen. This can reduce times of retraction for complex model and save printing time, but make slicing and G-code generation slower.

en: Don't support the whole bridge area which makes support very large. Bridge usually can be printing directly without support if not very long
en: Don't support the whole bridge area in order to use less support. Shorter bridges can usually be printed directly without support.

en: Download failed, File size exception.
en: Download failed; File size exception.

en: Download failed, unknown file format.
en: Download failed; unknown file format.

en: Enable LOD
en: Enable/Disable LOD

en: Enable clumping detection
en: Enable clumping detection by probing

en: Enable pressure advance, auto calibration result will be overwriten once enabled. Useless for QIDI Printer
en: Enable pressure advance? Auto calibration results will be overwritten once enabled. Note: this is useless for QIDI Printers.

en: Enable this option if machine has auxiliary part cooling fan
en: Enable this option if the machine has an auxiliary part cooling fan

en: Enable this option to add EXCLUDE OBJECT command in g-code for klipper firmware printer
en: Enable this option to add an EXCLUDE OBJECT command in g-code for printers running klipper firmware.

en: Enable this option to optimize part cooling fan speed for overhang and bridge to get better cooling
en: Enable this option to optimize the part cooling fan speed for overhangs and bridges to get better cooling

en: Enable this option to slow printing down by height
en: Enable this option to set the upper bound of printing speed and acceleration as functions of printing height (z) when z lies within the range ["starting height", "ending height"]. For example, the upper bound of the printing speed at z changes between "starting speed" and "ending speed" by z linearly.

en: Enable this option to slow printing down for different overhang degree
en: Enable this option to slow down when printing overhangs. The speeds for different overhang percentages are set below.

en: Enable this option to slow printing speed down to make the final layer time not shorter than the layer time threshold in "Max fan speed threshold", so that layer can be cooled for a longer time. This can improve the cooling quality for needle and small details
en: Enable this option to slow printing speed down to make the final layer time not shorter than the layer time threshold in "Max fan speed threshold" so that the layer can be cooled for more time. This can improve the quality for fine details

en: Enable this to add line number(Nx) at the beginning of each G-Code line
en: Enable this to add line number(Nx) at the beginning of each G-Code line.

en: Enable this to enable the camera on printer to check the quality of first layer
en: Enable this to allow the camera on the printer to check the quality of the first layer.

en: Enable this to get a G-code file which has G2 and G3 moves. And the fitting tolerance is the same as resolution
en: Enable this to get a G-code file which has G2 and G3 moves. The fitting tolerance is the same as resolution

en: Enqueued
en: Queued

en: Ensure seam placement away from overhangs for alignment and backing modes.
en: Ensure seam placement away from overhangs for alignment modes.

en: Entity Only
en: Entity only

en: Expand the first raft or support layer to improve bed plate adhesion, -1 means auto
en: Expands the first raft or support layer to improve bed plate adhesion, -1 means auto

en: Experimental feature.Retracting and cutting off the filament at a longer distance during changes to minimize purge.While this reduces flush significantly, it may also raise the risk of nozzle clogs or other printing problems.
en: Experimental feature: Retracting and cutting off the filament at a longer distance during changes to minimize purge.While this reduces flush significantly, it may also raise the risk of nozzle clogs or other printing problems.

en: Experimental feature.Retraction length before cutting off during filament change
en: Experimental feature. Retraction length before cutting off during filament change

en: Experimental feature: Retracting and cutting off the filament at a greater distance during filament changes to minimize flush.Although it can notably reduce flush,  it may also elevate the risk of nozzle clogs or other printing complications.
en: Experimental feature: Retracting and cutting off the filament at a greater distance during filament changes to minimize flush. Although it can notably reduce flush,  it may also elevate the risk of nozzle clogs or other printing complications.

en: Experimental feature: Retracting and cutting off the filament at a greater distance during filament changes to minimize flush.Although it can notably reduce flush, it may also elevate the risk of nozzle clogs or other printing complications.Please use with the latest printer firmware.
en: Experimental feature: Retracting and cutting off the filament at a greater distance during filament changes to minimize flush. Although it can notably reduce flush, it may also elevate the risk of nozzle clogs or other printing complications. Please use with the latest printer firmware.

en: Expirment feature to compensate the circle holes and circle contour. This feature is used to improve the accuracy of the circle holes and contour within the diameter below 50mm. Only support PLA Basic, PLA CF, PET CF, PETG CF and PETG HF.
en: Experimental feature to compensate the circle holes and circle contour. This feature is used to improve the accuracy of the circle holes and contour within the diameter below 50mm. Only support PLA Basic, PLA CF, PET CF, PETG CF and PETG HF.

en: Export result
en: Export Result

en: Extruders count
en: Extruder count

en: Failed to calculate line width of %1%. Can not get value of "%2%"
en: Failed to calculate line width of %1%. Cannot get value of “%2%”

en: Failed to download the plug-in. Please check your firewall settings and vpn software, check and retry.
en: Failed to download the plug-in. Please check your firewall settings and vpn software and retry.

en: Failed to generate gcode for invalid custom G-code.
en: Failed to generate G-code for invalid custom G-code.

en: Failed to install the plug-in. Please check whether it is blocked or deleted by anti-virus software.
en: Failed to install the plug-in. Please check whether it is blocked or has been deleted by anti-virus software.

en: Failed to save gcode file.
    Error message: %1%.
    Source file %2%.
en: Failed to save G-code file.
    Error message: %1%.
    Source file %2%.

en: Failed to send. Click Retry to attempt sending again. If retrying does not work, please check the reason.
en: Failed to send. Click 'Retry' to try again. If it still doesn’t work, please check the failure reason.

en: Failed to upload print file to FTP. Please check the network status and try again.
en: Failed to upload print file via FTP. Please check the network status and try again.

en: Fan speed for overhang
en: Fan speed for overhangs

en: Fatal error, exception caught: %1%
en: Fatal error; exception caught: %1%

en: Featue 1
en: Feature 1

en: Fetching model infomations ...
en: Fetching model information ...

en: Filament Tangle Detect
en: Filament Tangle Detection

en: Filament count exceeds the maximum number that painting tool supports. only the first %1% filaments will be available in painting tool.
en: Filament count exceeds the maximum number that painting tool supports. Only the first %1% filaments will be available in painting tool.

en: Filament diameter is used to calculate extrusion in gcode, so it's important and should be accurate
en: Filament diameter is used to calculate extrusion variables in G-code, so it is important that this is accurate and precise.

en: Filament serial is not inputed, please input serial.
en: Filament serial missing; please input serial.

en: Filament to print support base and raft. "Default" means no specific filament for support and current filament is used
en: Filament to print support bases and rafts. "Default" means no specific filament for support, and current filament is used

en: Filament to print support interface. "Default" means no specific filament for support interface and current filament is used
en: Filament to print support interfaces. "Default" means no specific filament for support interface, and current filament is used

en: Flow Rate Calibration measures the ratio of expected to actual extrusion volumes. The default setting works well in QIDI Tech printers and official filaments as they were pre-calibrated and fine-tuned. For a regular filament, you usually won't need to perform a Flow Rate Calibration unless you still see the listed defects after you have done other calibrations. For more details, please check out the wiki article.
en: Flow Rate Calibration measures the ratio of expected to actual extrusion volumes. The default setting works well with QIDI Tech printers and official filaments as they were pre-calibrated and fine-tuned. For a regular filament, you usually won't need to perform a Flow Rate Calibration unless you still see the listed defects after you have done other calibrations. For more details, please check out our wiki article.

en: Flush into support/objects/infill
    Did you know that you can save the wasted filament by flushing them into support/objects/infill during filament change?
en: Flush into support/objects/infill
    Did you know that you can reduce wasted filament by flushing it into support/objects/infill during filament changes?

en: Following line %s contains reserved keywords.
    Please remove it, or will beat G-code visualization and printing time estimation. | Following lines %s contain reserved keywords.
    Please remove them, or will beat G-code visualization and printing time estimation.
en[0]: Following line %s contains reserved keywords.
    Please remove it, or G-code visualization and print time estimation will be broken.
en[1]: Following lines %s contain reserved keywords.
    Please remove them, or G-code visualization and print time estimation will be broken.

en: Following model object has been repaired | Following model objects have been repaired
en[0]: The following model object has been repaired
en[1]: The following model objects have been repaired

en: Following preset will be deleted too. | Following presets will be deleted too.
en[0]: The following preset will be deleted too:
en[1]: The following presets will be deleted too:

en: For more information, please check out Wiki
en: For more information, please check out our Wiki

en: Force cooling fan to be specific speed when overhang degree of printed part exceeds this value. Expressed as percentage which indicides how much width of the line without support from lower layer. 0% means forcing cooling for all outer wall no matter how much overhang degree
en: Force cooling fan to be a specific speed when overhang degree of printed part exceeds this value. This is expressed as a percentage which indicates how much width of the line without support from lower layer. 0% means forcing cooling for all outer wall no matter the overhang degree.

en: Force cooling for overhang and bridge
en: Force cooling for overhangs and bridges

en: Force part cooling fan to be at this speed when printing bridge or overhang wall which has large overhang degree. Forcing cooling for overhang and bridge can get better quality for these part
en: Force part cooling fan to be at this speed when printing bridges or overhang walls which have a large overhang degree. Forcing cooling for overhangs and bridges can improve quality for these parts.

en: Found following keys unrecognized:
en: The following unrecognized keys have been found:

en: G-code path is generated after simplifying the contour of model to avoid too many points and gcode lines in the gcode file. Smaller value means higher resolution and more time to slice
en: G-code path is generated after simplifying the contour of model to avoid too many points and g-code lines in the g-code file. Smaller values mean higher resolution and longer slicing times.

en: Get ticket from device timeout
en: Timeout getting ticket from device

en: Height of initial layer. Making initial layer height thick slightly can improve build plate adhension
en: Height of initial layer. Making initial layer height slightly thicker can improve build plate adhesion.

en: Helio does not support using a number of materials greater than 1.
en: Helio simulation does not support using more than 1 material.

en: Helio: file succesfully uploaded
en: Helio: file successfully uploaded

en: Higher chamber temperature can help suppress or reduce warping and potentially lead to higher interlayer bonding strength for high temperature materials like ABS, ASA, PC, PA and so on.At the same time, the air filtration of ABS and ASA will get worse.While for PLA, PETG, TPU, PVA and other low temperature materials,the actual chamber temperature should not be high to avoid cloggings, so 0 which stands for turning off is highly recommended
en: Higher chamber temperature can help suppress or reduce warping and potentially lead to higher interlayer bonding strength for high temperature materials like ABS, ASA, PC, PA and so on. At the same time, the air filtration of ABS and ASA will get worse.While for PLA, PETG, TPU, PVA and other low temperature materials, the actual chamber temperature should not be high to avoid clogs, so 0 (turned off) is highly recommended.

en: Holes of object will be grown or shrunk in XY plane by the configured value. Positive value makes holes bigger. Negative value makes holes smaller. This function is used to adjust size slightly when the object has assembling issue
en: Holes in objects will be grown or shrunk in the XY plane by the set value. Positive values make holes bigger and negative values make holes smaller. This function is used to adjust size slightly when objects have assembly issues.

en: How to use calibration result?
en: How can I use calibration results?

en: How to use keyboard shortcuts
    Did you know that QIDI Studio offers a wide range of keyboard shortcuts and 3D scene operations.
en: How to use keyboard shortcuts
    Did you know that QIDI Studio offers a wide range of keyboard shortcuts and 3D scene operations?

en: If enable this setting, part cooling fan will never be stopped and will run at least at minimum speed to reduce the frequency of starting and stopping
en: Enabling this setting means that the part cooling fan will run continuously at minimum speed instead of stopping to reduce the frequency of starting and stopping.

en: If enabled, bridges are more reliable, can bridge longer distances, but may look worse. If disabled, bridges look better but are reliable just for shorter bridged distances.
en: If enabled, bridges are more reliable and can bridge longer distances but may look worse. If disabled, bridges look better but are reliable only for shorter distances.

en: If smooth or traditional mode is selected, a timelapse video will be generated for each print. After each layer is printed, a snapshot is taken with the chamber camera. All of these snapshots are composed into a timelapse video when printing completes. If smooth mode is selected, the toolhead will move to the excess chute after each layer is printed and then take a snapshot. Since the melt filament may leak from the nozzle during the process of taking a snapshot, prime tower is required for smooth mode to wipe nozzle.
en: If smooth or traditional mode is selected, a timelapse video will be generated for each print. After each layer is printed, a snapshot is taken with the chamber camera. All of these snapshots are composed into a timelapse video when printing completes. If smooth mode is selected, the toolhead will move to the excess chute after each layer is printed and then take a snapshot. Since the melt filament may leak from the nozzle during the process of taking a snapshot, a prime tower is required for smooth mode to wipe the nozzle.

en: If you want to have tighter or looser assemble, you can set this value. When it is positive, it indicates tightening, otherwise, it indicates loosening
en: If you want to have tighter or looser assembly, you can set this value. When it is positive, it indicates a tighter fit, otherwise, it indicates a looser fit.

en: If you want to process the output G-code through custom scripts, just list their absolute paths here. Separate multiple scripts with a semicolon. Scripts will be passed the absolute path to the G-code file as the first argument, and variables of settings also can be read
en: If you want to process the output G-code through custom scripts, just list their absolute paths here. Separate multiple scripts with a semicolon. Scripts will be passed via the absolute path to the G-code file as the first argument, and variables of settings can also be read

en: If your firmware requires relative E values, check this, otherwise leave it unchecked. Must use relative e distance for QIDI printer
en: If your firmware requires relative E values, check this, otherwise leave it unchecked. Must use relative e distance for QIDI printers.

en: Ignore HTTPS certificate revocation checks in case of missing or offline distribution points. One may want to enable this option for self signed certificates if connection fails.
en: Ignore HTTPS certificate revocation checks in the case of missing or offline distribution points. One may want to enable this option for self signed certificates if connection fails.

en: In order to reduce the visibility of the seam in a closed loop extrusion, the loop is interrupted and shortened by a specified amount.
    This amount as a percentage of the current extruder diameter. The default value for this parameter is 15
en: In order to reduce the visibility of the seam in a closed loop extrusion, the loop is interrupted and shortened by a specified amount.
    This amount is expressed as a percentage of the current extruder diameter. The default value for this parameter is 15.

en: InFo
en: Info

en: Infill area is enlarged slightly to overlap with wall for better bonding. The percentage value is relative to line width of sparse infill
en: This allows the infill area to be enlarged slightly to overlap with walls for better bonding. The percentage value is relative to line width of sparse infill.

en: Insert Gcode between objects. This parameter will only come into effect when you print your models object by object
en: Insert G-code between objects. This parameter will only come into effect when you print your models object by object.

en: Intersection operation requires at least two volumes.
en: Intersection operation requires at least two parts.

en: Ironing is using small flow to print on same height of surface again to make flat surface more smooth. This setting controls which layer being ironed
en: Ironing uses a small flow to print at the same height of a surface to make flat surfaces smoother. This setting controls which layers are being ironed.

en: It has a general layer height, and results in general layer lines and printing quality. It is suitable for most general printing cases.
en: It has a normal layer height, and results in average layer lines and print quality. It is suitable for most printing cases.

en: It has a small layer height, and results in almost negligible layer lines and high printing quality. It is suitable for most general printing cases.
en: It has a small layer height, and results in almost negligible layer lines and high print quality. It is suitable for most general printing cases.

en: It has a very big layer height, and results in very apparent layer lines, low printing quality and general printing time.
en: It has a very big layer height, and results in very apparent layer lines, low print quality and shorter printing time.

en: Lay on face
en: Lay on Face

en: Left Time
en: Remaining Time

en: Line pattern of bottom surface infill, not bridge infill
en: This is the line pattern of bottom surface infill, not including bridge infill.

en: Line width of initial layer
en: Line width of first layer

en: Line width of inner wall
en: Line width of inner walls

en: Loading G-codes
en: Loading G-code

en: Long retraction when cut(experimental)
en: Long retraction when cut (experimental)

en: Long retraction when extruder change
en: Long retraction when changing extruders

en: Max length of bridges that don't need support. Set it to 0 if you want all bridges to be supported, and set it to a very large value if you don't want any bridges to be supported.
en: This is the maximum length of bridges that don't need support. Set it to 0 if you want all bridges to be supported, and set it to a very large value if you don't want any bridges to be supported.

en: Maximum detour distance for avoiding crossing wall. Don't detour if the detour distance is larger than this value. Detour length could be specified either as an absolute value or as percentage (for example 50%) of a direct travel path. Zero to disable
en: Maximum detour distance for avoiding crossing wall. Don't detour if the detour distance is larger than this value. Detour length could be specified either as an absolute value or as percentage (for example 50%) of a direct travel path. 0 disables this feature.

en: Maximum distance to move points in XY to try to achieve a smooth spiralIf expressed as a %, it will be computed over nozzle diameter
en: Maximum distance to move points in XY to try to achieve a smooth spiral. If expressed as a %, it will be computed over nozzle diameter

en: Maximum printable height which is limited by mechanism of printer
en: This is the maximum printable height which is limited by the height of the build area.

en: Maximum width of a segmented region. Zero disables this feature.
en: Maximum width of a segmented region. A value of 0 disables this feature.

en: Maybe parts of the object at these height are too thin, or the object has faulty mesh
en: Parts of the object at these heights may be too thin or the object may have a faulty mesh.

en: Minimum HRC of nozzle required to print the filament. Zero means no checking of nozzle's HRC.
en: Minimum HRC of nozzle required to print the filament. A value of 0 means no checking of the nozzle's HRC.

en: Minimum thickness of thin features. Model features that are thinner than this value will not be printed, while features thicker than the Minimum feature size will be widened to the Minimum wall width. It's expressed as a percentage over nozzle diameter
en: Minimum thickness of thin features. Model features that are thinner than this value will not be printed, while features thicker than the minimum feature size will be widened to the minimum wall width. It's expressed as a percentage over nozzle diameter

en: Modified G-codes
en: Modified G-code

en: Modified Value(New)
en: Modified Value (New)

en: Modify paramters of right nozzle
en: Modify parameters of right nozzle

en: Move nozzle along the last extrusion path when retracting to clean leaked material on nozzle. This can minimize blob when printing new part after travel
en: Move nozzle along the last extrusion path when retracting to clean leaked material on nozzle. This can minimize blobs when printing new parts after traveling.

en: Move selection 10 mm in negative X direction
en: Move selection 10mm in negative X direction

en: Move selection 10 mm in negative Y direction
en: Move selection 10mm in negative Y direction

en: Move selection 10 mm in positive X direction
en: Move selection 10mm in positive X direction

en: Move selection 10 mm in positive Y direction
en: Move selection 10mm in positive Y direction

en: Movement step set to 1 mm
en: Movement step set to 1mm

en: No overlapping region found. Boolean intersection failed.
en: No overlapping region found. Boolean intersection failed. Ensure that all items in the list overlap each other.

en: No warnings when loading 3MF with modified G-codes
en: No warnings when loading 3MF with modified G-code

en: Not apply
en: Not applied

en: Note: AstroBox version at least 1.1.0 is required.
en: Note: AstroBox version 1.1.0 or higher is required.

en: Note: OctoPrint version at least 1.1.0 is required.
en: Note: OctoPrint version 1.1.0 or higher is required.

en: Note: Only filament-loaded slots can be selected.
en: Note: Only slots with filament loaded can be selected.

en: Note: Repetier version at least 0.90.0 is required.
en: Note: Repetier version 0.90.0 or higher is required.

en: Nozzle may be blocked when the temperature is out of recommended range.
    Please confirm whether to use the temperature for printing.
en: Nozzle may be blocked when the temperature is out of recommended range.
    Please confirm in order to use the temperature for printing.

en: Number of loops for the skirt. Zero means disabling skirt
en: This is the number of loops for the skirt. 0 means the skirt is disabled.

en: Official Filament
en: Official Filaments

en: On OSX there is always only one instance of app running by default. However it is allowed to run multiple instances of same app from the command line. In such case this settings will allow only one instance.
en: On OSX there is always only one instance of app running by default. However it is allowed to run multiple instances of same app from the command line. In such case this setting will allow only one instance.

en: Only display printer names with changes to printer, filament, and process presets.
en: Only display printers with changes to printer, filament, and process presets are displayed.

en: Only trigger retraction when the travel distance is longer than this threshold
en: Only trigger retraction when the travel distance is longer than this threshold.

en: Order of wall/infill. false means print wall first.
en: Order of wall/infill. If this is unchecked, walls will be printed before infill.

en: Overrider filament scarf seam setting and could control settings by modifier.
en: Override filament scarf seam setting and could control settings by modifier.

en: PPA-CF is brittle and could break in bended PTFE tube above Toolhead.
en: PPA-CF is brittle and could break in a bent PTFE tube above the Toolhead.

en: PPS-CF is brittle and could break in bended PTFE tube above Toolhead.
en: PPS-CF is brittle and could break in a bent PTFE tube above the Toolhead.

en: Part cooling fan speed may be increased when auto cooling is enabled. This is the maximum speed limitation of part cooling fan
en: The part cooling fan speed may be increased when auto cooling is enabled. This is the maximum speed for the part cooling fan.

en: Part cooling fan speed will be max when the estimated layer time is shorter than the setting value
en: The part cooling fan will run at maximum speed when the estimated layer time is shorter than the threshold value.

en: Part cooling fan speed will start to run at min speed when the estimated layer time is no longer than the layer time in setting. When layer time is shorter than threshold, fan speed is interpolated between the minimum and maximum fan speed according to layer printing time
en: The part cooling fan will run at the minimum fan speed when the estimated layer time is longer than the threshold value. When the layer time is shorter than the threshold, the fan speed will be interpolated between the minimum and maximum fan speed according to layer printing time.

en: Part cooling fan will be enabled for layers of which estimated time is shorter than this value. Fan speed is interpolated between the minimum and maximum fan speeds according to layer printing time
en: The part cooling fan will be enabled for layers where the estimated time is shorter than this value. Fan speed is interpolated between the minimum and maximum fan speeds according to layer printing time.

en: Part of the calibration failed! You may clean the plate and retry. The failed test result would be dropped.
en: Part of the calibration failed! It may help to clean the plate and retry. The failed test result will be deleted.

en: Parts
en: Part

en: Perform
en: Apply

en: Personal assecc token is empty, please fill in the correct token.
en: Personal access token is empty, please fill in the correct token.

en: Plate% d: %s is not suggested to be used to print filament %s(%s). If you still want to do this printing, please set this filament's bed temperature to non zero.
en: Plate% d: %s is not suggested for use printing filament %s(%s). If you still want to do this print job, please set this filament's bed temperature to a number that is not zero.

en: Please change the desiccant when it is too wet. The indicator may not represent accurately in following cases : when the lid is open or the desiccant pack is changed. it take hours to absorb the moisture, low temperatures also slow down the process.
en: *Please change the desiccant when it is too wet. The indicator may not represent accurately in following cases：when the lid is open or the desiccant pack is changed, it take hours to absorb the moisture; low temperatures also slow down the process.

en: Please check the network and try again, You can restart or update the printer if the issue persists.
en: Please check the network and try again. You can restart or update the printer if the issue persists.

en: Please confirm explosion ratio = 1,and please select at least one object
en: Please confirm explosion ratio = 1, and please select at least one object

en: Please correct them in the param tabs
en: Please correct them in the Param tabs

en: Please do not mix-use the Ext with AMS
en: Please avoid using AMS filaments and external spool filament simultaneously.

en: Please enter the IP of printer to connect.
en: Please enter the IP of the printer to connect.

en: Please find the corner with perfect degree of extrusion
en: Please find the corner with the perfect degree of extrusion

en: Please go to filament setting to edit your presets if you need.
    Please note that nozzle temperature, hot bed temperature, and maximum volumetric speed has a significant impact on printing quality. Please set them carefully.
en: Please go to filament settings to edit your presets if you need to.
    Please note that nozzle temperature, hot bed temperature, and maximum volumetric speed each have a significant impact on printing quality. Please set them carefully.

en: Please note that the model show will undergo certain changes at small pixels case.
    Enabled LOD requires application restart.
en: Please note that the model display may change when using smaller pixel sizes.
    Changing LOD settings requires restarting the application.

en: Please select a type you want to export
en: Please select a preset type you want to export

en: Portions copyright
en: License Info

en: Power on update
en: Update on startup

en: Preset "%1%" already exists and is incompatible with current printer.
en: Preset "%1%" already exists and is incompatible with the current printer.

en: Preset path is not found, please reselect vendor.
en: Preset path is not found; please reselect vendor.

en: Preset(Old)
en: Preset (Old)

en: Pressure advance(Klipper) AKA Linear advance factor(Marlin). Useless for QIDI Printer
en: Pressure advance(Klipper) AKA Linear advance factor(Marlin). Useless for QIDI Printers

en: Preview only mode:
    The loaded file contains gcode only, Can not enter the Prepare page
en: Preview only mode:
    The loaded file contains G-code only, cannot enter the Prepare page

en: Prime tower is required for clumping detection. There may be flaws on the model without prime tower. Are you sure you want to disable prime tower?
en: Prime tower is required for clumping detection by probing. There may be flaws on the model without prime tower. Are you sure you want to disable prime tower?

en: Prime tower is required for clumping detection. There may be flaws on the model without prime tower. Do you still want to enable clumping detection?
en: Prime tower is required for clumping detection by probing. There may be flaws on the model without prime tower. Do you still want to enable clumping detection?

en: Prime tower is required for clumping detection; otherwise, there may be flaws on the model.
en: Prime tower is required for clumping detection by probing. There may be flaws on the model without prime tower.

en: Prime tower is required for smooth timelapse. There may be flaws on the model without prime tower. Do you want to enable prime tower?
en: A prime tower is required for smooth timelapse mode. There may be flaws on the model without prime tower. Do you want to enable the prime tower?

en: Prime tower is required for smooth timeplase. There may be flaws on the model without prime tower. Are you sure you want to disable prime tower?
en: A Prime tower is required for smooth timeplase mode. There may be flaws on the model without a prime tower. Are you sure you want to disable the prime tower?

en: Print By Object: 
    Suggest to use auto-arrange to avoid collisions when printing.
en: Print By Object: 
    We suggest using auto-arrange to avoid collisions when printing.

en: Print file not found, Please slice it again and send it for printing.
en: Print file not found; please slice it again and send it for printing.

en: Print sequence, layer by layer or object by object
en: This determines the print sequence, allowing you to print layer-by-layer or object-by-object.

en: Printer and all the filament&process presets that belong to the printer. 
    Can be shared with others.
en: Printer and all the filament & process presets that belong to the printer,
    Can be shared with others

en: Printing Silk Filament
    Did you know that Silk filament needs special consideration to print it successfully? Higher temperature and lower speed are always recommended for the best results.
en: Printing Silk Filament
    Did you know that Silk filament needs special consideration to print successfully? A higher temperature and lower speed are always recommended for the best results.

en: Problem occured. Please update the printer firmware and try again.
en: A problem occurred. Please update the printer firmware and try again.

en: Pull back current filament
en: Pull back the current filament

en: Purging after filament change will be done inside objects' infills. This may lower the amount of waste and decrease the print time. If the walls are printed with transparent filament, the mixed color infill will be seen outside. It will not take effect, unless the prime tower is enabled.
en: Purging after filament change will be done inside objects' infills. This may lower the amount of waste and decrease the print time. If the walls are printed with transparent filament, the mixed color infill will be visible. It will not take effect unless the prime tower is enabled.

en: Purging after filament change will be done inside objects' support. This may lower the amount of waste and decrease the print time. It will not take effect, unless the prime tower is enabled.
en: Purging after filament change will be done inside objects' support. This may lower the amount of waste and decrease the print time. It will not take effect unless a prime tower is enabled.

en: QIDI Cool Plate SuperTack
en: Cool Plate SuperTack

en: QIDI Studio is based on PrusaSlicer by Prusa Research, which is from Slic3r by Alessandro Ranellucci and the RepRap community
en: QIDI Studio is based on PrusaSlicer by Prusa Research, which is based on Slic3r by Alessandro Ranellucci and the RepRap community

en: QIDIStudio will terminate because of a localization error. It will be appreciated if you report the specific scenario this issue happened.
en: QIDIStudio will terminate because of a localization error. We would appreciate it if you report the specific scenario in which this issue happened.

en: QIDIStudio will terminate because of running out of memory.It may be a bug. It will be appreciated if you report the issue to our team.
en: QIDIStudio will terminate because of running out of memory. It may be a bug. We would greatly appreciate it if you report the issue to our team.

en: Randomly jitter while printing the wall, so that the surface has a rough look. This setting controls the fuzzy position
en: This setting makes the toolhead randomly jitter while printing walls so that the surface has a rough textured look. This setting controls the fuzzy position.

en: Recommended nozzle temperature of this filament type is [%d, %d] degree centigrade
en: The recommended nozzle temperature for this filament type is [%d, %d] degrees centigrade

en: Recommended nozzle temperature range of this filament. 0 means no set
en: Recommended nozzle temperature range of this filament. 0 means not set

en: Refreshing the historical Flow Dynamics Calibration records
en: Refreshing the previous Flow Dynamics Calibration records

en: Retraction distance when extruder change
en: Retraction distance when changing extruders

en: Right button click the icon to drop the object printable property
en: Right click the icon to drop the object printable property

en: Right button click the icon to drop the object settings
en: Right click the icon to drop the object settings

en: Same as Global Bed Type
en: Same as Global Plate Type

en: Sending gcode file to sdcard
en: Sending gcode file to Micro SD card

en: Set parameters for multiple objects
    Did you know that you can set slicing parameters for all selected objects at one time?
en: Set parameters for multiple objects
    Did you know that you can set slicing parameters for all selected objects at once?

en: Should not large than 100%.
    Reset to defualt
en: Should not larger than 100%.
    Reset to default

en: Should not large than layer height.
    Reset to 10%
en: Should not be greater than layer height.
    Reset to 10%

en: Show the list of the keyboard shortcuts
en: Show the list of keyboard shortcuts

en: Shrink the initial layer on build plate to compensate for elephant foot effect
en: This shrinks the first layer on the build plate to compensate for elephant foot effect.

en: Slice all plate to obtain time and filament estimation
en: Slice all plates to obtain time and filament estimation

en: Slicing height for each layer. Smaller layer height means more accurate and more printing time
en: This is the height for each layer. Smaller layer heights give greater accuracy but longer printing time.

en: Slow down for overhang
en: Slow down for overhangs

en: Smoothing outwall speed in z direction to get better surface quality. Print time will increases. It is not work on spiral vase mode.
en: Smoothing outer wall speed in z direction to get better surface quality: Print time will increase. This is not work in spiral vase mode.

[ctx: Software]
en: Update
en: Update now

en: Soluble material is commonly used to print support and support interface
en: Soluble material is commonly used to print support and support interfaces

en: Some amount of material in extruder is pulled back to avoid ooze during long travel. Set zero to disable retraction
en: This is the amount of filament in the extruder that is pulled back to avoid oozing during long travel distances. Set to 0 to disable retraction.

en: Spacing of bottom interface lines. Zero means solid interface
en: This is the spacing of bottom interface lines. 0 means solid interface.

en: Sparse infill area which is smaller than threshold value is replaced by internal solid infill
en: Sparse infill areas which are smaller than this threshold value are replaced by internal solid infill.

en: Specify the URL of your device user interface if it's not same as print_host
en: Specify the URL of your device user interface if it's not the same as print_host

en: Speed for reloading filament into extruder. Zero means the same speed as retraction
en: Speed for reloading filament into extruder: 0 means the same speed as retraction

en: Speed of auxiliary part cooling fan. Auxiliary fan will run at this speed during printing except the first several layers which are defined by no cooling layers
en: Speed of auxiliary part cooling fan. The auxiliary fan will run at this speed during printing, except for the first several layers, which are defined by no cooling layers

en: Speed of exhaust fan during printing.This speed will overwrite the speed in filament custom gcode
en: Speed of exhaust fan during printing.This speed will override the speed in filament custom g-code

en: Speed of gap infill. Gap usually has irregular line width and should be printed more slowly
en: This is the speed for gap infill. Gaps usually have irregular line width and should be printed more slowly.

en: Speed of initial layer except the solid infill part
en: This is the speed for the first layer except for solid infill sections.

en: Speed of internal solid infill, not the top and bottom surface
en: This is the speed for internal solid infill, not including the top or bottom surface.

en: Speed of outer wall which is outermost and visible. It's used to be slower than inner wall speed to get better quality.
en: This is the printing speed for the outer walls of parts. These are generally printed slower than inner walls for higher quality.

en: Speed up your print with Adaptive Layer Height
    Did you know that you can print a model even faster, by using the Adaptive Layer Height option? Check it out!
en: Speed up your print with Adaptive Layer Height
    Did you know that you can print a model even faster by using the Adaptive Layer Height option? Check it out!

en: Spiralize smooths out the z moves of the outer contour. And turns a solid model into a single walled print with solid bottom layers. The final generated model has no seam
en: This enables spiraling, which smooths out the Z moves of the outer contour and turns a solid model into a single walled print with solid bottom layers. The final generated model has no seam.

en: Split to objects
en: Split to Objects

en: Split to parts
en: Split to Parts

en: Studio will remember build plate selected last time for certain printer model.
en: Studio will remember build plate selected last time for certain printer models.

en: Support control chamber temperature
en: Support controlling chamber temperature

en: Support filament
en: Filament for Supports

en: Support material is commonly used to print support and support interface
en: Support material is commonly used to print support and support interfaces.

en: Support painting
en: Support Painting

en: Support will be generated for overhangs whose slope angle is below the threshold.
en: Support will be generated for overhangs whose slope angle is below this threshold.

en: Switch to rectilinear pattern?
    Yes - switch to rectilinear pattern automatically
    No  - reset density to default non 100% value automatically
en: Switch to rectilinear pattern?
    Yes - switch to rectilinear pattern
    No  - reset density to default non 100% value

en: Switching the language requires application restart.
en: Switching languages requires the application to restart.

en: Synchronizing device information time out
en: Synchronizing device information timed out

en: Temporarily closed because there is no operation for a while.
en: Temporarily closed because there is no activity for a while.

en: Text mesh ie empty.
en: Text mesh is empty.

en: Thank you for purchasing a QIDI Tech device.Before using your QIDI Tech device, please read the termsand conditions.By clicking to agree to use your QIDI Tech device, you agree to abide by the Privacy Policy and Terms of Use(collectively, the "Terms"). If you do not comply with or agree to the QIDI Tech Privacy Policy, please do not use QIDI Tech equipment and services.
en: Thank you for purchasing a QIDI Tech device. Before using your QIDI Tech device, please read the terms and conditions. By clicking to agree to use your QIDI Tech device, you agree to abide by the Privacy Policy and Terms of Use (collectively, the "Terms"). If you do not comply with or agree to the QIDI Tech Privacy Policy, please do not use QIDI Tech equipment and services.

en: The '%s' folder already exists in the current directory. Do you want to clear it and rebuild it.
    If not, a time suffix will be added, and you can modify the name after creation.
en: The '%s' folder already exists in the current directory. Do you want to clear it and rebuild it?
    If not, a time suffix will be added, and you can modify the name after creation.

en: The .gcode.3mf file contains no G-code data.Please slice it whth QIDI Studio and export a new .gcode.3mf file.
en: The .gcode.3mf file contains no G-code data.Please slice it with QIDIStudio and export a new .gcode.3mf file.

en: The 3mf has following modified G-codes in filament or printer presets:
en: The 3mf has following modified G-code in filament or printer presets:

en: The 3mf is generated by old QIDI Studio, load geometry data only.
en: The 3mf was generated by an old version of QIDI Studio, loading geometry data only.

en: The AMS will automatically read the filament information when inserting a new QIDI Tech filament. This takes about 20 seconds.
en: The AMS will automatically read the filament information when inserting a new QIDI Tech filament spool. This takes about 20 seconds.

en: The AMS will automatically read the information of inserted filament on start-up. It will take about 1 minute.The reading process will roll filament spools.
en: The AMS will automatically read the information of inserted filament on start-up. It will take about 1 minute.The reading process will rotate the filament spools.

en: The Filament name %s you created already exists. 
    If you continue creating, the preset created will be displayed with its full name. Do you want to continue?
en: The Filament name %s you created already exists. 
    If you continue, the preset created will be displayed with its full name. Do you want to continue?

en: The QIDI Studio needs an upgrade
en: QIDI Studio needs an update

en: The QIDI Studio version is too old to enable cloud service. Please download the latest version from QIDI Tech website.
en: The QIDI Studio version is too old to enable cloud service. Please download the latest version from QIDI Tech's website.

en: The SLA archive doesn't contain any presets. Please activate some SLA printer preset first before importing that SLA archive.
en: The SLA archive doesn't contain any presets. Please activate some SLA printer presets first before importing that SLA archive.

en: The Wipe option is not available when using the Firmware Retraction mode.
    
    Shall I disable it in order to enable Firmware Retraction?
en: The Wipe option is not available when using the Firmware Retraction mode.
    
    Disable it in order to enable Firmware Retraction?

en: The actual flushing volumes is equal to the flush multiplier multiplied by the flushing volumes in the table.
en: The actual flushing volumes is equal to the flush multiplier value multiplied by the flushing volumes in the table.

en: The amount of material to extrude during ironing. Relative to flow of normal layer height. Too high value results in overextrusion on the surface
en: This is the amount of material to be extruded during ironing. It is relative to the flow of normal layer height. Too high a value will result in overextrusion on the surface.

en: The application cannot run normally because OpenGL version is lower than 2.0.
en: The application cannot run normally because your OpenGL version is lower than 2.0.

en: The configuration may be generated by a newer version of QIDIStudio.
en: The configuration may have been generated by a newer version of QIDI Studio.

en: The configuration package is incompatible with current application.
    %s will update the configuration package, Otherwise it won't be able to start
en: The configuration package is incompatible with the current application.
    %s will update the configuration package to allow the application to start.

en: The current chamber temperature or the target chamber temperature exceeds 45℃.In order to avoid extruder clogging,low temperature filament(PLA/PETG/TPU) is not allowed to be loaded.
en: The current chamber temperature or the target chamber temperature exceeds 45℃. In order to avoid extruder clogging, low temperature filament (PLA/PETG/TPU) is not allowed to be loaded.

en: The current firmware version of the printer does not support calibration.
    Please upgrade the printer firmware.
en: The current firmware version of the printer does not support calibration.
    Please update the printer firmware.

en: The current hot bed temperature is relatively high. The nozzle may be clogged when printing this filament in a closed enclosure. Please open the front door and/or remove the upper glass.
en: The current heatbed temperature is relatively high. The nozzle may clog when printing this filament in a closed environment. Please open the front door and/or remove the upper glass.

en: The current printer preset cannot be sliced using Helio.
en: The current printer preset cannot be used with Helio.

en: The current project has unsaved changes, save it before continue?
en: The current project has unsaved changes. Would you like to save before continuing?

en: The current project has unsaved changes, save it before continuing?
en: The current project has unsaved changes. Would you like to save before continuing?

en: The currently connected printer '%s', is a %s model but not consistent with preset in project file.
    To use this printer for printing, please switch the preset first.
en: The currently connected printer '%s' is a %s model but not consistent with preset in project file.
    To use this printer for printing, please switch the preset first.

en: The currently connected printer '%s', is a %s model.
    To use this printer for printing, please switch the printer model of project file to %s.
en: The currently connected printer '%s' is a %s model.
    To use this printer for printing, please switch the printer model of project file to %s.

en: The default acceleration of both normal printing and travel except initial layer
en: This is the default acceleration for both normal printing and travel after the first layer.

en: The filament type setting of external spool is different from the filament in the slicing file.
en: The filament type setting of external spool is different from the filament in the slicing file, 
     which may cause printing issues.

en: The file %s already exists
    Do you want to replace it?
en: The file %s already exists.
    Do you want to replace it?

en: The firmware version is abnormal. Repairing and updating are required before printing. Do you want to update now? You can also update later on printer or update next time starting the studio.
en: The firmware version is abnormal. Repairing and updating are required before printing. Do you want to update now? You can also update later on the printer or update next time you start QIDI Studio.

en: The height finishes slowing down, Ending height should be larger than Starting height, or the slowing down will not work!
en: “Ending height” should be larger than “Starting height”, or the slowing down will not work!

en: The largest printable layer height for extruder. Used to limit the maximum layer height when enable adaptive layer height
en: The largest printable layer height for extruder. Used to limit the maximum layer height when using adaptive layer height

en: The length of fast retraction before wipe, relative to retraction length
en: This is the length of fast retraction before a wipe, relative to retraction length.

en: The localization tag of build plate is detected, and printing is paused if the tag is not in predefined range.
en: The localization tag of the build plate will be detected, and printing will be paused if the tag is not in predefined range.

en: The lowest printable layer height for extruder. Used to limit the minimum layer height when enable adaptive layer height
en: The lowest printable layer height for extruder. Used to limit the minimum layer height when using adaptive layer height

en: The material may have volumetric change after switching between molten state and crystalline state. This setting changes all extrusion flow of this filament in gcode proportionally. Recommended value range is between 0.95 and 1.05. Maybe you can tune this value to get nice flat surface when there has slight overflow or underflow
en: The material may have volumetric change after switching between molten and crystalline states. This setting changes all extrusion flow of this filament in G-code proportionally. The recommended value range is between 0.95 and 1.05. You may be able to tune this value to get a nice flat surface if there is slight overflow or underflow.

en: The material softens at this temperature, so when the bed temperature is equal to or greater than it, it's highly recommended to open the front door and/or remove the upper glass to avoid cloggings.
en: The material softens at this temperature, so when the bed temperature is equal to or greater than this, it's highly recommended to open the front door and/or remove the upper glass to avoid clogs.

en: The metallic material of nozzle. This determines the abrasive resistance of nozzle, and what kind of filament can be printed
en: The metallic material of the nozzle: This determines the abrasive resistance of the nozzle and what kind of filament can be printed.

en: The model is not fond, place reselect vendor.
en: The model was not found; please reselect vendor.

en: The name is not allowed to end with space character.
en: The name is not allowed to end with a space.

en: The name is not allowed to start with space character.
en: The name is not allowed to start with a space.

en: The nozzle diameter is not fond, place reselect.
en: The nozzle diameter was not found; please reselect.

en: The nozzle hardness required by the filament is higher than the default nozzle hardness of the printer. Please replace the hardened nozzle or filament, otherwise, the nozzle will be attrited or damaged.
en: The nozzle hardness required by the filament is higher than the default nozzle hardness of the printer. Please replace the hardened nozzle or filament, otherwise, the nozzle will be worn down or damaged.

en: The number of bottom solid layers is increased when slicing if the thickness calculated by bottom shells layers is thinner than this value. This can avoid having too thin shell when layer height is small. 0 means that this setting is disabled and thickness of bottom shell is absolutely determained by bottom shell layers
en: The number of bottom solid layers is increased when slicing if the thickness calculated by bottom shells layers is thinner than this value. This can avoid having an overly thin shell when layer height is small. 0 means that this setting is disabled and thickness of bottom shell is determined by bottom shell layers.

en: The number of top solid layers is increased when slicing if the thickness calculated by top shell layers is thinner than this value. This can avoid having too thin shell when layer height is small. 0 means that this setting is disabled and thickness of top shell is absolutely determained by top shell layers
en: The number of top solid layers is increased when slicing if the thickness calculated by top shell layers is thinner than this value. This can avoid having too thin a shell when layer height is small. 0 means that this setting is disabled and thickness of top shell is determined simply by the number of top shell layers.

en: The object from file %s is too small, and maybe in meters or inches.
     Do you want to scale to millimeters?
en: The object from file %s is too small, and may be in meters or inches.
     Do you want to scale to millimeters?

en: The player is not loaded, please click "play" button to retry.
en: The player is not loaded; please click the "play" button to retry.

en: The portion of the model's outer surface within a certain depth range is called the skin. This parameter is used to adjust the density of this section.When two regions have the same sparse infill settings but different skin densities, This area will not be split into two separate regions.default is as same as infill density.
en: The portion of the model's outer surface within a certain depth range is called the skin. This parameter is used to adjust the density of this section.When two regions have the same sparse infill settings but different skin densities, This area will not be split into two separate regions. Default is the same as infill density.

en: The prime tower is not supported in "By object" print.
en: A prime tower is not supported in “By object” print.

en: The prime tower is not supported when adaptive layer height is on. It requires that all objects have the same layer height.
en: A prime tower is not supported when adaptive layer height is on. It requires that all objects have the same layer height.

en: The prime tower requires "support gap" to be multiple of layer height
en: A prime tower requires any “support gap” to be a multiple of layer height.

en: The prime tower requires that all objects are printed over the same number of raft layers
en: A prime tower requires that all objects are printed over the same number of raft layers.

en: The prime tower requires that all objects are sliced with the same layer heights.
en: A prime tower requires that all objects are sliced with the same layer height.

en: The prime tower requires that support has the same layer height as object.
en: The prime tower requires that supports have the same layer height as objects.

en: The printer is busy on other print job
en: The printer is busy with another print job.

en: The printer preset is not fond, place reselect.
en: The printer preset was not found; please reselect.

en: The printer preset you created already has a preset with the same name. Do you want to overwrite it?
    	Yes: Overwrite the printer preset with the same name, and filament and process presets with the same preset name will be recreated 
    and filament and process presets without the same preset name will be reserve.
    	Cancel: Do not create a preset, return to the creation interface.
en: The printer preset you created already has a preset with the same name. Do you want to overwrite it?
    	Yes: Overwrite the printer preset with the same name, and filament and process presets with the same preset name will be recreated 
    and filament and process presets without the same preset name will be reserved.
    	Cancel: Do not create a preset; return to the creation interface.

en: The printing job will be stopped. Continue?
en: The print job will be stopped. Continue?

en: The printing speed in exported gcode will be slowed down, when the estimated layer time is shorter than this value, to get better cooling for these layers
en: The printing speed in exported G-code will be slowed down when the estimated layer time is shorter than this value in order to get better cooling for these layers.

en: The remaining part of the model contour after removing a certain depth from the surface is called the skeleton. This parameter is used to adjust the density of this section.When two regions have the same sparse infill settings but different skeleton densities, their skeleton areas will develop overlapping sections.default is as same as infill density.
en: The remaining part of the model contour after removing a certain depth from the surface is called the skeleton. This parameter is used to adjust the density of this section.When two regions have the same sparse infill settings but different skeleton densities, their skeleton areas will develop overlapping sections. Default is the same as infill density.

en: The selected file contains several disjoint areas. This is not supported.
en: The selected file contains several disjointed areas. This is not supported.

en: The spiral vase mode does not work when an object contains more than one materials.
en: Spiral (vase) mode does not work when an object contains more than one material.

en: The target object contains only one part and can not be split.
en: The target object contains only one part and cannot be split.

en: The vendor can not be a number. Please re-enter.
en: The vendor can not be a number; please re-enter.

en: The volume of material to prime extruder on tower.
en: This is the volume of material to prime the extruder with on the tower.

en: The width within which to jitter. It's adversed to be below outer wall line width
en: The width of jittering: it’s recommended to keep this lower than the outer wall line width.

en: The wipe speed is determined by the speed setting specified in this configuration.If the value is expressed as a percentage (e.g. 80%), it will be calculated based on the travel speed setting above.The default value for this parameter is 80%
en: The wipe speed is determined by the speed setting specified in this configuration. If the value is expressed as a percentage (e.g. 80%), it will be calculated based on the travel speed setting above. The default value for this parameter is 80%.

en: The wiping tower can be used to clean up the residue on the nozzle and stabilize the chamber pressure inside the nozzle, in order to avoid appearance defects when printing objects.
en: The wiping tower can be used to clean up residue on the nozzle and stabilize the chamber pressure inside the nozzle in order to avoid appearance defects when printing objects.

en: There are some unknown filaments in the AMS mappings. Please check whether they are the required filaments. If they are okay, press "Confirm" to start printing.
en: There are some unknown filaments in the AMS mappings. Please check whether they are the required filaments. If they are okay, click "Confirm" to start printing.

en: There is already a historical calibration result with the same name: %s. Only one of the results with the same name is saved. Are you sure you want to override the historical result?
en: There is already a previous calibration result with the same name: %s. Only one result with a name is saved. Are you sure you want to overwrite the previous result?

en: There many parts of the software that come from community contributions, so we're unable to list them one-by-one, and instead, they'll be attributed in the corresponding code comments.
en: There are many parts of the software that come from community contributions, so we're unable to list them one-by-one, and instead, they'll be attributed in the corresponding code comments.

en: There may be escape characters in the vendor or serial input of filament. Please delete and re-enter.
en: There may be disallowed characters in the vendor or serial input of the filament. Please delete and re-enter.

en: This G-code will be used as a code for the pause print. User can insert pause G-code in gcode viewer
en: This G-code will be used as a code for the pause print. Users can insert pause G-code in the G-code viewer.

en: This action will break a cut correspondence.
    After that model consistency can't be guaranteed .
    
    To manipulate solid parts or negative volumes you have to invalidate cut information first.
en: This action will break a cut correspondence.
    After that, model consistency can't be guaranteed.
    
    To manipulate solid parts or negative volumes you have to invalidate cut information first.

en: This controls the generation of the brim at outer and/or inner side of models. Auto means the brim width is analysed and calculated automatically.
en: This controls the generation of the brim at outer and/or inner side of models. Auto means the brim width is analyzed and calculated automatically.

en: This factor affects the amount of material for top solid infill. You can decrease it slightly to have smooth surface finish
en: This factor affects the amount of material for top solid infill. You can decrease it slightly to have a smooth surface finish.

en: This file contains several objects positioned at multiple heights.
    Instead of considering them as multiple objects, should 
    the file be loaded as a single object having multiple parts?
en: This file contains several objects positioned at multiple heights.
    Instead of considering them as multiple objects, should 
    the file be loaded as a single object with multiple parts?

en: This file is not from a trusted site, do you want to open it anyway?
en: This file is not from a trusted site; do you want to open it anyway?

en: This gcode is inserted when change filament, including T command to trigger tool change
en: This G-code is inserted when filament is changed, including T commands to trigger tool change.

en: This is neither a commonly used filament, nor one of QIDI filaments, and it varies a lot from brand to brand. So, it's highly recommended to ask its vendor for suitable profile before printing and adjust some parameters according to its performances.
en: This is neither a commonly used filament, nor a QIDI filament, and it varies a lot from brand to brand, so it's highly recommended to ask the vendor for a suitable profile before printing and adjust some parameters according to its performance.

en: This is the number of solid layers of top shell, including the top surface layer. When the thickness calculated by this value is thinner than top shell thickness, the top shell layers will be increased
en: This is the number of solid layers of top shell, including the top surface layer. When the thickness calculated by this value is thinner than the top shell thickness, the top shell layers will be increased

en: This machine type can only hold %d history results per nozzle.
en: This machine type can only hold %d historical results per nozzle.

en: This machine type can only hold %d history results per nozzle. This result will not be saved.
en: This machine type can only hold %d historical results per nozzle. This result will not be saved.

en: This machine type can only hold 16 history results per nozzle. You can delete the existing historical results and then start calibration. Or you can continue the calibration, but you cannot create new calibration historical results. 
    Do you still want to continue the calibration?
en: This machine type can only hold 16 historical results per nozzle. You can delete the existing historical results and then start calibration. Or you can continue the calibration, but you cannot create new calibration historical results. 
    Do you still want to continue the calibration?

en: This object contains non-part components.
en: This object contains non-model parts.

en: This object will be used to purge the nozzle after a filament change to save filament and decrease the print time. Colours of the objects will be mixed as a result. It will not take effect, unless the prime tower is enabled.
en: This object will be used to purge the nozzle after a filament change to save filament and decrease the print time. Colors of the objects will be mixed as a result. It will not take effect unless the prime tower is enabled.

en: This option will auto detect narrow internal solid infill area. If enabled, concentric pattern will be used for the area to speed printing up. Otherwise, rectilinear pattern is used defaultly.
en: This option will auto-detect narrow internal solid infill areas. If enabled, the concentric pattern will be used for the area to speed up printing. Otherwise, the rectilinear pattern will be used by default.

en: This plate is locked,
    We can not do auto-arrange on this plate.
en: This plate is locked.
    We cannot auto-arrange this plate.

en: This plate is locked,
    We can not do auto-orient on this plate.
en: This plate is locked.
    We cannot auto-orient this plate.

en: This setting determines the maximum overhang angle that t he branches of tree support allowed to make.If the angle is increased, the branches can be printed more horizontally, allowing them to reach farther.
en: This setting determines the maximum overhang angle that the branches of tree support are allowed to make. If the angle is increased, the branches can be printed more horizontally, allowing them to reach farther.

en: This setting is only used for model size tuning with small value in some cases.
    For example, when the model size has slight errors and is difficult be assembled.
    For large size tuning, please use model scaling function.
    
    The value will be reset to 0.
en: This setting is only used for model size tuning with small values in some cases.
    For example, when the model size has slight errors and assembly is difficult.
    For large size tuning, please use the model scaling function.
    
    The value will be reset to 0.

en: This setting stands for how much volume of filament can be melted and extruded per second. Printing speed is limited by max volumetric speed, in case of too high and unreasonable speed setting. Can't be zero
en: This setting is the volume of filament that can be melted and extruded per second. Printing speed is limited by max volumetric speed, in case of too high and unreasonable speed setting. This value cannot be zero.

en: Time to load new filament when switch filament. For statistics only
en: Time to load new filament when switching filament, for statistical purposes only.

en: Time to switch extruder. For statistics only
en: Time for switching extruder. For statistics only

en: Time to unload old filament when switch filament. For statistics only
en: Time to unload old filament when switching filament, for statistical purposes only.

en: Timelapse is not supported while the storage does not exist.
en: Timelapse is not supported when storage is not inserted.

en: Timelapse is not supported while the storage is unavailable.
en: Timelapse is not supported when storage is unavailable.

en: Tips for calibration material: 
    - Materials that can share same hot bed temperature
    - Different filament brand and family(Brand = QIDI, Family = Basic, Matte)
en: Tips for calibration material: 
    - Materials that can share same hot bed temperature
    - Different filament brand and family (Brand = QIDI, Family = Basic, Matte, etc.)

en: Too large elephant foot compensation is unreasonable.
    If really have serious elephant foot effect, please check other settings.
    For example, whether bed temperature is too high.
    
    The value will be reset to 0.
en: Too large an elephant foot compensation is a problem.
    For very serious elephant foot effects, please check other settings.
    For example, bed temperature may be too high.
    
    The value will be reset to 0.

en: Too large layer height.
    Reset to 0.2
en: Layer height too large
    It has been reset to 0.2

en: Too large line width
en: Line width too large

en: Too small ironing spacing.
    Reset to 0.1
en: Ironing spacing too small
    It has been reset to 0.1

en: Too small layer height.
    Reset to 0.2
en: Layer height too small
    It has been reset to 0.2

en: Too small line width
en: Line width too small

en: Too small max volumetric speed.
    Reset to 0.5
en: Too small max volumetric speed.
    Value was reset to 0.5

en: Turning off the lights during the task will cause the failure of AI monitoring, like spaghetti detection. Please choose carefully.
en: Turning the lights off during a task will cause the failure of AI monitoring such as spaghetti detection. Please choose carefully.

en: Undefine
en: Undefined

en: Union operation requires at least two volumes.
en: Union operation requires at least two parts.

en: Unknown file format. Input file must have .3mf or .zip.amf extension.
en: Unknown file format: input file must have .3mf or .zip.amf extension.

en: Unknown file format. Input file must have .stl, .obj, .amf(.xml) extension.
en: Unknown file format: input file must have .stl, .obj, or .amf(.xml) extension.

en: Upload filename doesn't end with "%s". Do you wish to continue?
en: Filename to upload doesn't end with "%s". Do you want to continue?

en: Use Immediately
en: Use Now

en: Use only one wall on flat top surface, to give more space to the top infill pattern. Could be applied on topmost surface or all top surface.
en: Use only one wall on flat top surface to give more space to the top infill pattern. Can be applied on topmost surface or all top surfaces

en: Vendor is not found, please reselect.
en: Vendor is not found; please reselect.

en: Vendor is not selected, please reselect vendor.
en: Vendor is not selected; please reselect vendor.

en: Volume of nozzle between the cutter and the end of nozzle
en: Volume of nozzle between the filament cutter and the end of the nozzle

en: Warning:please select Plane's feature.
en: Warning: please select Plane's feature.

en: Warning:please select Point's or Circle's feature.
en: Warning: please select Point's or Circle's feature.

en: Warning:please select two different mesh.
en: Warning: please select two different meshes.

en: We now have added the auto-calibration for different filaments, which is fully automated and the result will be saved into the printer for future use. You only need to do the calibration in the following limited cases:
    1. If you introduce a new filament of different brands/models or the filament is damp;
    2. if the nozzle is worn out or replaced with a new one;
    3. If the max volumetric speed or print temperature is changed in the filament setting.
en: We now have added auto-calibration for different filaments, which is fully automated and the result will be saved to the printer for future use. You only need to do the calibration in the following limited cases:
    1. If you introduce a new filament of different brands/models or the filament is damp
    2. If the nozzle is worn out or replaced with a new one;
    3. If the max volumetric speed or print temperature is changed in the filament setting.

en: We would rename the presets as "Vendor Type Serial @printer you selected". 
    To add preset for more prinetrs, Please go to printer selection
en: We would rename the presets as "Vendor Type Serial @printer you selected". 
    To add preset for more printers; please go to printer selection

en: When enable spiral vase mode, machines with I3 structure will not generate timelapse videos.
en: When spiral vase mode is enabled, machines with I3 structure will not generate timelapse videos.

en: When need to print with the printer door opened
    Did you know that opening the printer door can reduce the probability of extruder/hotend clogging when printing lower temperature filament with a higher enclosure temperature. More info about this in the Wiki.
en: When do you need to print with the printer door opened?
    Did you know that opening the printer door can reduce the probability of extruder/hotend clogging when printing lower temperature filament with a higher enclosure temperature? There is more info about this in the Wiki.

en: When sparse infill density is low, the internal solid infill or internal bridge may have no archor at the end of line. This causes falling and bad quality when printing internal solid infill. When enable this feature, loop paths will be added to the sparse fill of the lower layers for specific thickness, so that better archor can be provided for internal bridge. 0 means disable this feature
en: When sparse infill density is low, the internal solid infill or internal bridge may have no anchor at the end of lines. This causes falling and decreased quality when printing internal solid infill. When this feature is enabled, loop paths will be added to the sparse fill of the lower layers to attain a specific thickness, so that better anchoring can be provided for internal bridges. 0 disables this feature.

en: When the current material run out, the printer will continue to print in the following order.
en: When the current material runs out, the printer will continue to print materials in the following order.

en: When transitioning between different numbers of walls as the part becomes thinner, a certain amount of space is allotted to split or join the wall segments. It's expressed as a percentage over nozzle diameter
en: When transitioning between different numbers of walls as the part becomes thinner, a certain amount of space is allotted to split or join the wall segments. It's expressed as a percentage over nozzle diameter.

en: When you set the chamber temperature below 40℃, the chamber temperature control will not be activated. And the target chamber temperature will automatically be set to 0℃.
en: When you set the chamber temperature below 40℃, the chamber temperature control will not be activated, and the target chamber temperature will automatically be set to 0℃.

en: Whenever the retraction is done, the nozzle is lifted a little to create clearance between nozzle and the print. It prevents nozzle from hitting the print when travel moves. Using spiral line to lift z can prevent stringing
en: Whenever there is a retraction, the nozzle is lifted a little to create clearance between the nozzle and the print. This prevents the nozzle from hitting the print when traveling. Using a spiral line to lift z can prevent stringing.

en: Whether the machine supports silent mode in which machine use lower acceleration to print
en: Whether the machine supports silent mode in which machine uses lower acceleration to print more quietly

en: While printing by Object, the extruder may collide skirt.
    Thus, reset the skirt layer to 1 to avoid that.
en: While printing by object, the extruder may collide with a skirt.
    Thus, reset the skirt layer to 1 to avoid collisions.

en: Would you like to log in this printer with current account?
en: Would you like to log in this printer with the current account?

en: You could change the Flow Dynamics Calibration Factor in material editing
en: You can change the Flow Dynamics Calibration Factor in material editing

en: You have completed printing the mall model, 
    but the synchronization of rating information has failed.
en: You have completed printing the mall model, 
    but synchronizing rating information has failed.

en: You have entered an illegal input in the printable area section on the first page. Please check before creating it.
en: You have entered a disallowed character in the printable area section on the first page. Please use only numbers.

en: You have not selected the vendor and model or inputed the custom vendor and model.
en: You have not selected the vendor and model or input the custom vendor and model.

en: You have not yet selected the printer to replace the nozzle, please choose.
en: You have not yet selected the printer to replace the nozzle for; please choose a printer.

en: You try to delete an object which is a part of a cut object.
    This action will break a cut correspondence.
    After that model consistency can't be guaranteed.
en: You are trying to delete an object which is a part of a cut object.
    This action will break a cut correspondence.
    After that, model consistency can't be guaranteed.

en: Your comment result cannot be uploaded due to some reasons. As follows:
    
      error code:
en: Your comment result cannot be uploaded due to the following reasons:
    
      error code:

en: Your model needs support ! Please make support material enable.
en: Your model needs support! Please enable support material.

en: Your object appears to be too large, Do you want to scale it down to fit the heat bed automatically?
en: Your object appears to be too large, Do you want to scale it down to fit the print bed automatically?

en: Z gap between object and raft. Ignored for soluble interface
en: This is the Z gap between an object and a raft. It is ignored for soluble interfaces.

en: Zero initial layer height is invalid.
    
    The first layer height will be reset to 0.2.
en: Zero first layer height is invalid.
    
    The first layer height will be reset to 0.2.

en: archive too large
en: Archive too large

en: buffer too small
en: Buffer too small

en: connectors is out of object
en: Connectors must be on object surface.

en: file too large
en: File too large

en: keyboard 1-9: set filament for object/part
en: Keyboard 1-9: set filament for object/part

en: lock depth should smaller than skin depth.
    Reset to 50%% of skin depth
en: lock depth should smaller than skin depth.
    Reset to half of skin depth

en: minute each batch.(It depends on how long it takes to complete the heating.)
en: minute each batch. (It depends on how long it takes to complete heating.)

en: non-manifold edges be caused by cut tool, do you want to fix it now?
en: Non-manifold edges be caused by cut tool: do you want to fix now?

en: normal(auto) and tree(auto) is used to generate support automatically. If normal(manual) or tree(manual) is selected, only support enforcers are generated
en: normal(auto) and tree(auto) are used to generate support automatically. If normal(manual) or tree(manual) is selected, only support enforcers are generated

en: printers at the same time.(It depends on how many devices can undergo heating at the same time.)
en: printers at the same time. (It depends on how many devices can undergo heating at the same time.)

en: the Configuration package is incompatible with current APP.
en: The configuration package is incompatible with the current version of QIDI Studio.

en: the configuration package is incompatible with current application.
en: the configuration package is incompatible with the current application.
