The fan parameters are optimized

resources/profiles/QIDITechnology.ini

@@ -5,7 +5,7 @@
 name = QIDI Technology
 # Configuration version of this file. Config file will only be installed, if the config_version differs.
 # This means, the server may force the QIDISlicer configuration to be downgraded.
-config_version = 1.0.5
+config_version = 1.0.6
 # Where to get the updates from?
 config_update_url = https://github.com/QIDITECH/QIDISlicer/releases/download/QIDITechnology/
 changelog_url = https://qidi3d.com/pages/software-firmware
@@ -84,7 +84,7 @@ first_layer_acceleration_over_raft = 500
 first_layer_extrusion_width = 0.5
 first_layer_height = 0.2
 first_layer_infill_speed = 100
-first_layer_speed = 55
+first_layer_speed = 50
 first_layer_speed_over_raft = 30
 first_layer_travel_speed = 300
 fuzzy_skin = none
@@ -340,17 +340,25 @@ volume_temperature = 0
 inherits = *common*
 advance_pressure = 0.021
 bed_temperature = 90
+disable_fan_first_layers = 3
 enable_auxiliary_fan = 0
+enable_dynamic_fan_speeds = 1
 enable_volume_fan = 40
-extrusion_multiplier = 0.95
+extrusion_multiplier = 0.92
+fan_below_layer_time = 30
 filament_colour = #FFFACD
 filament_density = 1.02
 filament_max_volumetric_speed = 22
 filament_type = ABS
 first_layer_bed_temperature = 90
 first_layer_temperature = 250
-max_fan_speed = 60
-min_fan_speed = 60
+max_fan_speed = 50
+min_fan_speed = 10
+overhang_fan_speed_0 = 100
+overhang_fan_speed_1 = 90
+overhang_fan_speed_2 = 80
+overhang_fan_speed_3 = 80
+slowdown_below_layer_time = 4
 temperature = 270
 volume_temperature = 55
 
@@ -358,17 +366,25 @@ volume_temperature = 55
 inherits = *common*
 advance_pressure = 0.021
 bed_temperature = 90
+disable_fan_first_layers = 3
 enable_auxiliary_fan = 0
+enable_dynamic_fan_speeds = 1
 enable_volume_fan = 40
 extrusion_multiplier = 0.95
+fan_below_layer_time = 30
 filament_colour = #FFC800
 filament_density = 1.02
 filament_max_volumetric_speed = 22
 filament_type = ABS
 first_layer_bed_temperature = 90
 first_layer_temperature = 250
-max_fan_speed = 60
-min_fan_speed = 60
+max_fan_speed = 80
+min_fan_speed = 10
+overhang_fan_speed_0 = 100
+overhang_fan_speed_1 = 90
+overhang_fan_speed_2 = 80
+overhang_fan_speed_3 = 80
+slowdown_below_layer_time = 4
 temperature = 270
 volume_temperature = 55
 
@@ -377,6 +393,7 @@ inherits = *common*
 advance_pressure = 0.01
 bed_temperature = 100
 bridge_fan_speed = 0
+disable_fan_first_layers = 3
 enable_auxiliary_fan = 0
 enable_volume_fan = 0
 extrusion_multiplier = 0.95
@@ -396,17 +413,25 @@ volume_temperature = 55
 inherits = *common*
 advance_pressure = 0.021
 bed_temperature = 90
+disable_fan_first_layers = 3
 enable_auxiliary_fan = 0
+enable_dynamic_fan_speeds = 1
 enable_volume_fan = 40
-extrusion_multiplier = 0.95
+extrusion_multiplier = 0.92
+fan_below_layer_time = 35
 filament_colour = #F0E68C
 filament_density = 1.02
-filament_max_volumetric_speed = 22
+filament_max_volumetric_speed = 16
 filament_type = ABS
 first_layer_bed_temperature = 90
 first_layer_temperature = 250
-max_fan_speed = 60
-min_fan_speed = 60
+max_fan_speed = 50
+min_fan_speed = 10
+overhang_fan_speed_0 = 100
+overhang_fan_speed_1 = 80
+overhang_fan_speed_2 = 60
+overhang_fan_speed_3 = 40
+slowdown_below_layer_time = 4
 temperature = 270
 volume_temperature = 55
 
@@ -414,68 +439,86 @@ volume_temperature = 55
 inherits = *common*
 advance_pressure = 0.01
 bed_temperature = 80
-bridge_fan_speed = 0
+bridge_fan_speed = 40
+disable_fan_first_layers = 3
 enable_auxiliary_fan = 0
 extrusion_multiplier = 0.96
+fan_below_layer_time = 5
 filament_colour = #696969
 filament_density = 1.09
 filament_max_volumetric_speed = 14
 filament_type = PA12-CF
 first_layer_bed_temperature = 80
 first_layer_temperature = 290
-max_fan_speed = 15
-min_fan_speed = 15
+max_fan_speed = 30
+min_fan_speed = 10
+slowdown_below_layer_time = 2
 temperature = 290
 
 [filament:*QIDI PAHT-CF*]
 inherits = *common*
 advance_pressure = 0.01
 bed_temperature = 80
-bridge_fan_speed = 0
+bridge_fan_speed = 40
+disable_fan_first_layers = 3
 enable_auxiliary_fan = 0
 extrusion_multiplier = 0.96
+fan_below_layer_time = 5
 filament_colour = #4F4F4F
 filament_density = 1.20
 filament_max_volumetric_speed = 15
 filament_type = PAHT-CF
 first_layer_bed_temperature = 80
 first_layer_temperature = 310
-max_fan_speed = 15
-min_fan_speed = 15
+max_fan_speed = 30
+min_fan_speed = 10
+slowdown_below_layer_time = 2
 temperature = 310
 
 [filament:*QIDI PET-CF*]
 inherits = *common*
 advance_pressure = 0.01
 bed_temperature = 80
-bridge_fan_speed = 5
+bridge_fan_speed = 40
+disable_fan_first_layers = 3
 enable_auxiliary_fan = 0
 extrusion_multiplier = 1
+fan_below_layer_time = 5
 filament_colour = #323232
 filament_density = 1.30
 filament_max_volumetric_speed = 14
 filament_type = PET-CF
 first_layer_bed_temperature = 80
 first_layer_temperature = 320
-max_fan_speed = 10
+max_fan_speed = 30
 min_fan_speed = 10
+slowdown_below_layer_time = 2
 temperature = 320
 
 [filament:*QIDI PETG-Tough*]
 inherits = *common*
 advance_pressure = 0.07
 bed_temperature = 80
-bridge_fan_speed = 60
+bridge_fan_speed = 90
+disable_fan_first_layers = 3
 enable_auxiliary_fan = 0
+enable_dynamic_fan_speeds = 1
 extrusion_multiplier = 0.95
+fan_below_layer_time = 30
 filament_colour = #00FF40
 filament_density = 1.24
 filament_max_volumetric_speed = 16
 filament_type = PETG
 first_layer_bed_temperature = 80
 first_layer_temperature = 240
-max_fan_speed = 60
-min_fan_speed = 60
+max_fan_speed = 40
+min_fan_speed = 10
+min_print_speed = 10
+overhang_fan_speed_0 = 90
+overhang_fan_speed_1 = 70
+overhang_fan_speed_2 = 50
+overhang_fan_speed_3 = 40
+slowdown_below_layer_time = 8
 temperature = 250
 
 [filament:*QIDI PLA Rapido*]
@@ -491,7 +534,7 @@ filament_max_volumetric_speed = 22
 inherits = *common*
 advance_pressure = 0.03
 bed_temperature = 80
-bridge_fan_speed = 0
+bridge_fan_speed = 20
 enable_auxiliary_fan = 0
 extrusion_multiplier = 0.96
 filament_colour = #FFEBCD
@@ -509,26 +552,36 @@ temperature = 300
 inherits = *common*
 advance_pressure = 0.021
 bed_temperature = 90
+disable_fan_first_layers = 3
 enable_auxiliary_fan = 0
+enable_dynamic_fan_speeds = 1
 enable_volume_fan = 40
 extrusion_multiplier = 0.95
+fan_below_layer_time = 30
 filament_colour = #FFFF00
 filament_density = 1.04
-filament_max_volumetric_speed = 17.5
+filament_max_volumetric_speed = 17
 filament_type = ABS
 filament_vendor = Generic
 first_layer_bed_temperature = 90
 first_layer_temperature = 250
-max_fan_speed = 35
-min_fan_speed = 35
+max_fan_speed = 80
+min_fan_speed = 10
+overhang_fan_speed_0 = 100
+overhang_fan_speed_1 = 90
+overhang_fan_speed_2 = 80
+overhang_fan_speed_3 = 80
+slowdown_below_layer_time = 4
 temperature = 260
 
 [filament:*Generic PETG*]
 inherits = *common*
 advance_pressure = 0.07
 bed_temperature = 80
+disable_fan_first_layers = 3
 enable_auxiliary_fan = 0
 extrusion_multiplier = 0.95
+fan_below_layer_time = 30
 filament_colour = #00FF00
 filament_density = 1.27
 filament_max_volumetric_speed = 9
@@ -536,8 +589,10 @@ filament_type = PETG
 filament_vendor = Generic
 first_layer_bed_temperature = 80
 first_layer_temperature = 240
-max_fan_speed = 60
-min_fan_speed = 60
+max_fan_speed = 90
+min_fan_speed = 40
+min_print_speed = 10
+slowdown_below_layer_time = 4
 temperature = 250
 
 [filament:*Generic PLA*]
@@ -550,6 +605,7 @@ filament_vendor = Generic
 [filament:*Generic TPU 95A*]
 inherits = *common*
 advance_pressure = 0.1
+enable_auxiliary_fan = 0
 extrusion_multiplier = 1
 filament_colour = #8000FF
 filament_density = 1.21
@@ -557,6 +613,8 @@ filament_max_volumetric_speed = 6
 filament_type = TPU
 filament_vendor = Generic
 first_layer_temperature = 230
+min_print_speed = 10
+slowdown_below_layer_time = 8
 temperature = 230
 
 # X-MAX 3 QIDI filament preset
@@ -580,7 +638,7 @@ compatible_printers_condition = printer_model=="X-MAX 3"
 inherits = *QIDI PA12-CF*
 compatible_printers_condition = printer_model=="X-MAX 3"
 
-[filament:QIDI PAHT-CF @X-Plus3]
+[filament:QIDI PAHT-CF @X-MAX 3]
 inherits = *QIDI PAHT-CF*
 compatible_printers_condition = printer_model=="X-MAX 3"
 
@@ -727,7 +785,6 @@ inherits = *QIDI PETG-Tough*
 compatible_printers_condition = printer_model=="X-smart 3"
 advance_pressure = 0.048
 filament_max_volumetric_speed = 14
-slowdown_below_layer_time = 8
 
 [filament:QIDI PLA Rapido @X-smart 3]
 inherits = *QIDI PLA Rapido*
@@ -766,7 +823,6 @@ slowdown_below_layer_time = 8
 [filament:Generic TPU 95A @X-smart 3]
 inherits = *Generic TPU 95A*
 compatible_printers_condition = printer_model=="X-smart 3"
-slowdown_below_layer_time = 8
 
 # Common printer preset
 [printer:*common*]